
Disclaimer
How to change engine oil and filter on Honda Accord VIII CU – replacement guide
downloads:
34
Views:
673

Recommended replacement interval for the part category Oil filter : 1 year / 20000 km
Important!
This replacement procedure can be used for:
HONDA ACCORD VIII (CU) 2.0 i (CU1) … View more
The steps may slightly vary depending on the car design.
HONDA ACCORD VIII (CU) 2.0 i (CU1) … View more
The steps may slightly vary depending on the car design.
How to change oil filter and engine oil on HONDA ACCORD 8 (CU2) [TUTORIAL AUTODOC]

All the parts you need to replace – Oil Filter for ACCORD VIII (CU) and other HONDA models
Oil filter
Alternative products

Wire brush
Oil filter cup socket 76/14-F
Impact socket №10
Impact socket №17
Ratchet wrench
Torque wrench
Oil drain pan
Funnel
Fender cover
AUTODOC recommends:
- Replace the oil filter every time when changing motor oil.
- All work should be done with the engine stopped.
- Wear gloves to prevent contact with hot liquid.
Replacement: engine oil and filter – Honda Accord VIII CU. Use the following procedure:
- Step 1Open the hood.
- Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
- Step 3Unscrew the oil filler plug.
- Step 4Lift the car using a jack or place it over an inspection pit.Replacement: engine oil and filter – Honda Accord VIII CU. Tip from AUTODOC experts:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.All work should be done with the engine stopped.
- Step 5Unscrew the fasteners of the lower sound insulation. Use a drive socket #10. Use a ratchet wrench.
- Step 6Remove the lower sound insulation.
- Step 7Put a waste oil container with at least 5 l capacity under the drainage hole.
- Step 8Clean the area of the oil pan drainage hole. Use a wire brush.
- Step 9Unscrew the drain plug. Use a drive socket #17. Use a ratchet wrench.
- Step 10Drain the used oil.Replacement: engine oil and filter – Honda Accord VIII CU. Tip:Caution! The oil may be hot.
- Step 11Unscrew the oil filter. Use the 76/14-F socket.
- Step 12Prepare a container for the old oil filter. Put the old oil filter in the container.Replacement: engine oil and filter – Honda Accord VIII CU. Professionals recommend:Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter.
- Step 13Lubricate the rubber seal of the new filter with a little amount of fresh oil.
- Step 14Clean the oil filter seat.
- Step 15Screw the new filter into its place. Use the 76/14-F socket. Use a torque wrench. Tighten it to 22 nm torque.Replacement: engine oil and filter – Honda Accord VIII CU. AUTODOC recommends:Wait until the oil has completely drained from the drainage hole.
- Step 16Clean the area of the oil pan drainage hole.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the HONDA Accord VIII Saloon (CU) model
Popular maintenance tutorials for Honda Accord VIII CU
Complete guides for changing the Oil filters on different HONDA ACCORD models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your HONDA ACCORD VIII (CU)
View more
- 5 Essential Tips to Prepare Your Car for Winter | AUTODOC tips
- When, why, and how to change engine oil | AUTODOC tips
- How to Fix P0401 ✅ error code Insufficient EGR flow
- #DIY Tips for Fixing Your Car's Air Conditioning Issues | Don't Wait for Costly Repairs!
Most commonly replaced car parts on HONDA ACCORD
Time to replace parts? Get even better deals in our Shop app.

SCAN ME