Disclaimer
How to change engine oil and filter on Fiat Punto 188 petrol – replacement guide
downloads:
12
Views:
614
Recommended replacement interval for the part category Oil filter : 1 year / 20000 km
Important!
This replacement procedure can be used for:
FIAT PUNTO (188) 1.2 Natural Power, FIAT PUNTO (188) 1.2 16V 80 (188.233, .235, .253, .255, .333, .353, .639,..., FIAT PUNTO (188) 1.4 … View more
The steps may slightly vary depending on the car design.
FIAT PUNTO (188) 1.2 Natural Power, FIAT PUNTO (188) 1.2 16V 80 (188.233, .235, .253, .255, .333, .353, .639,..., FIAT PUNTO (188) 1.4 … View more
The steps may slightly vary depending on the car design.
How to change oil filter and engine oil on FIAT PUNTO 2 (188) [TUTORIAL AUTODOC]

All the parts you need to replace – Oil Filter for PUNTO (188) and other FIAT models
Alternative products

All-purpose cleaning spray
Oil filter cup socket 76-14F
HEX bit no.H12.
Ratchet wrench
Torque wrench
Oil drain pan
Funnel
Fender cover
Replacement: engine oil and filter – Fiat Punto 188. AUTODOC recommends:
- Replace the oil filter every time when changing motor oil.
- Use only new O-rings during installation.
- Wear gloves to prevent contact with hot liquid.
- All work should be done with the engine stopped.
Replacement: engine oil and filter – Fiat Punto 188. Use the following procedure:
- Step 1
Open the hood. - Step 2
Use a fender protection cover to prevent damaging paintwork and plastic parts of the car. - Step 3
Remove the cap of the oil filler neck. - Step 4
Lift the car using a jack or place it over an inspection pit.Replacement: engine oil and filter – Fiat Punto 188. Tip:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point. - Step 5
Put a waste oil container with at least 3 l capacity under the drainage hole. - Step 6
Unscrew the drain plug. Use HEX No.H12. Use a ratchet wrench. - Step 7
Drain the used oil.Replacement: engine oil and filter – Fiat Punto 188. Professionals recommend:Caution! The oil may be hot. - Step 8
Clean the oil filter seat. Use all-purpose cleaning spray. - Step 9Prepare a container for the old oil filter.Step 10
Unscrew the oil filter. Use the 76-14F socket. Use a ratchet wrench. - Step 11Put the old oil filter in the container.Replacement: engine oil and filter – Fiat Punto 188. Tip from AUTODOC experts:Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter.Step 12
Clean the oil filter seat. - Step 13
Lubricate the rubber seal of the new filter with a little amount of fresh oil. - Step 14
Screw the new filter into its place. Use the 76-14F socket. Use a torque wrench. Tighten it to 18 Nm torque.Replacement: engine oil and filter – Fiat Punto 188. Tip from AUTODOC:Wait until the oil has completely drained from the drainage hole. - Step 15Clean the area of the oil pan drainage hole.Step 16
Screw in the new drainage plug and tighten it. Use HEX No.H12. Use a torque wrench. Tighten it to 27 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the FIAT Punto II Hatchback (188) model
Popular maintenance tutorials for Fiat Punto Mk2
Complete guides for changing the Oil filters on different FIAT PUNTO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your FIAT PUNTO (188)
View more
How to Safely Wash Your Car in Winter Without Damage | AUTODOC tips
How to Make a DIY Foam Sprayer | AUTODOC tips
How to choose the right engine oil for your car | AUTODOC
How to Fix a Squealing Belt: Causes & Solutions | AUTODOC Expert Tips
Most commonly replaced car parts on FIAT PUNTO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME




























