
Disclaimer
How to change wheel cylinder on AUDI A2 (8Z0) – replacement guide
downloads:
8
Views:
91

Recommended replacement interval for the part category Wheel Brake Cylinder : 60000 km
Important!
This replacement procedure can be used for:
AUDI A2 (8Z0) 1.4 TDI, AUDI A2 (8Z0) 1.2 TDI, AUDI A2 (8Z0) 1.4, AUDI A2 (8Z0) 1.4 TDI … View more
The steps may slightly vary depending on the car design.
AUDI A2 (8Z0) 1.4 TDI, AUDI A2 (8Z0) 1.2 TDI, AUDI A2 (8Z0) 1.4, AUDI A2 (8Z0) 1.4 TDI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Wheel Cylinder for A2 (8Z0) and other AUDI models
Wheel Brake Cylinder
Alternative products

Wire brush
WD-40 spray
Copper grease
Combination spanner #7
Combination spanner #11
Torx bit T30
Wheel impact socket #17
Ratchet wrench
Torque wrench
Flat Screwdriver
Phillips screwdriver
Wheel chock
Replacement: wheel cylinder – AUDI A2 (8Z0). Tip from AUTODOC:
- Replace the wheel brake cylinders of the rear drum brakes in pairs.
- The replacement procedure is identical for the right and left wheel brake cylinders of the rear drum brakes.
- All work should be done with the engine stopped.
Replacement: wheel cylinder – AUDI A2 (8Z0). Recommended sequence of steps:
- Step 1Secure the wheels with chocks.
- Step 2Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 3Raise the rear of the car and secure on supports.Step 4Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. AUDI A2 (8Z0)
- Step 5Remove the wheel.
- Step 6Clean the brake drum fasteners. Use a wire brush. Use WD-40 spray.Step 7Unscrew the brake drum fastening. Use a Phillips screwdriver.
- Step 8Remove the brake drum.Replacement: wheel cylinder – AUDI A2 (8Z0). Tip from AUTODOC experts:Examine the brake drum. Replace it if necessary.
- Step 9Disconnect the hydraulic line from the wheel cylinder back. Use a combination spanner #11.Replacement: wheel cylinder – AUDI A2 (8Z0). Tip from AUTODOC:Immediately plug the brake line open end to prevent fluid leakage and ingress of dirt into the hydraulic system.
- Step 10Unscrew the brake cylinder fastening bolt. Use Torx T30. Use a ratchet wrench.
- Step 11Remove the brake cylinder from the backplate. Use a flat screwdriver.
- Step 12Clean the brake drum. Use a wire brush. Use WD-40 spray.Step 13Clean the brake pipe attachment spot and the brake drum fastening bolts on :maker :model.Step 14Install a new brake cylinder.
- Step 15Screw the brake cylinder fastening bolts. Use Torx T30. Use a torque wrench. Tighten it to 8 nm torque.
- Step 16Connect the hydraulic line to the wheel cylinder back. Use a combination spanner #11. Use a torque wrench. Tighten it to 14 nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the AUDI A2 (8Z0) model
Popular maintenance tutorials for AUDI A2 (8Z0)
Complete guides for changing the Brake wheel cylinder on different AUDI A2 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your AUDI A2 (8Z0)
View more
- Which Coolant is Best? Comparison Test | AUTODOC
- Preventing Engine Failure: Head Gasket Inspection Tutorial | AUTODOC
- Top 5 possible reasons your car is shaking or vibrating
- How to choose the right engine oil for your car | AUTODOC
Most commonly replaced car parts on AUDI A2
Time to replace parts? Get even better deals in our Shop app.

SCAN ME