
Disclaimer
How to change track rod end on VW Jetta Mk7 Saloon (BU3) – replacement guide
downloads:
0
Views:
6
Important!
This replacement procedure can be used for:
VW Jetta Mk7 Saloon (BU3) 1.4 TSI … View more
The steps may slightly vary depending on the car design.
VW Jetta Mk7 Saloon (BU3) 1.4 TSI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Track Rod End for Jetta Mk7 Saloon (BU3) and other VW models
Track rod end
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #22
Combination spanner #24
Drive socket # 18
Wheel impact socket #17
Ratchet wrench
Torque wrench
Tap wrench
Vernier caliper
Ball joint puller
Wheel chock
Replacement: track rod end – VW Jetta Mk7 Limousine (BU3). Tip from AUTODOC experts:
- Replace tie rod ends in pairs.
- The replacement procedure is identical for the right and left tie rod ends.
- All work should be done with the engine stopped.
Replacement: track rod end – VW Jetta Mk7 Limousine (BU3). Recommended sequence of steps:
- Step 1Secure the wheels with chocks.Step 2Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 3Raise the front of the car and secure on supports.Step 4Unscrew the wheel bolts.Replacement: track rod end – VW Jetta Mk7 Limousine (BU3). Tip:To avoid injury, hold up the wheel when unscrewing the bolts.
- Step 5Remove the wheel.
- Step 6Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.
- Step 7When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper.
- Step 8Loosen the lock nut securing the tie rod end to the tie rod. Use a combination spanner #24.
- Step 9Unscrew the end fastening nut to the steering knuckle. Use a drive socket #18. Use a tap wrench.
- Step 10Disconnect the tie rod end from the steering knuckle. Use a ball joint puller.
- Step 11Screw the end out of the tie rod.
- Step 12Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray.
- Step 13Screw on a new tie rod end.AUTODOC recommends:While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements.
- Step 14Connect the tie rod end to the steering knuckle.
- Step 15Screw on the fastening nut that connects the tie rod end to the steering knuckle. Use a drive socket #18. Use a ratchet wrench.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VW Jetta Mk7 Saloon (BU3) model
Popular maintenance tutorials for VW Jetta Mk7 Limousine (BU3)
Complete guides for changing the Tie rod end on different VW JETTA models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VW Jetta Mk7 Saloon (BU3)
View more
- How to Swap an M50 Engine in a BMW E30 Turbo | AUTODOC Project
- How to Order Car Parts Online: Avoid These 5 Common Pitfalls
- BMW E30 Turbo Suspension Swap: Boost Your Handling | AUTODOC project
- Unveiling the secrets: Detecting vacuum leaks with a Smoke Machine | AUTODOC
Most commonly replaced car parts on VW JETTA
Time to replace parts? Get even better deals in our Shop app.

SCAN ME