Disclaimer
How to change track rod end on SEAT Cordoba I Vario Box Body / Estate (6K5) – replacement guide
downloads:
0
Views:
3
Important!
This replacement procedure can be used for:
SEAT Cordoba I Vario Box Body / Estate (6K5) 1.9 TDI … View more
The steps may slightly vary depending on the car design.
SEAT Cordoba I Vario Box Body / Estate (6K5) 1.9 TDI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Track Rod End for Cordoba I Vario Box Body / Estate (6K5) and other SEAT models
Alternative products

Wire brush
WD-40 spray
All-purpose cleaning spray
Copper grease
Torque wrench
Combination spanner #19
Combination spanner #22
Drive socket # 19
Wheel impact socket #17
Ratchet wrench
Ball joint puller
Vernier caliper
Wheel chock
Replacement: track rod end – SEAT Cordoba I Vario Kasten / Kombi (6K5). Tip from AUTODOC:
- Replace tie rod ends in pairs.
- The replacement procedure is identical for the right and left tie rod ends.
- Please note: all work on the car – SEAT Cordoba I Vario Kasten / Kombi (6K5) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Secure the wheels with chocks.Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the car.Replacement: track rod end – SEAT Cordoba I Vario Kasten / Kombi (6K5). Tip:If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. SEAT Cordoba I Vario Kasten / Kombi (6K5) - Step 5
Remove the wheel. - Step 6
Clean all tie rod end connections. Use a wire brush. Use WD-40 spray. - Step 7
When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper. - Step 8
Loosen the lock nut securing the tie rod end to the tie rod. Use a combination spanner #19. Use a combination spanner #22. - Step 9
Unscrew the end fastening nut to the steering knuckle. Use a drive socket #19. Use a ratchet wrench. - Step 10
Disconnect the tie rod end from the steering knuckle. Use a ball joint puller. - Step 11
Screw the end out of the tie rod. - Step 12
Clean the mounting seats of the tie rod end. Use a wire brush. Use all-purpose cleaning spray. - Step 13
Treat the mounting seats of the tie rod end. Use copper grease. - Step 14
Screw on a new tie rod end. Use a vernier caliper.Replacement: track rod end – SEAT Cordoba I Vario Kasten / Kombi (6K5). AUTODOC experts recommend:While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the SEAT Cordoba I Vario Box Body / Estate (6K5) model
Popular maintenance tutorials for SEAT Cordoba I Vario Kasten / Kombi (6K5)
Complete guides for changing the Tie rod end on different SEAT CORDOBA models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your SEAT Cordoba I Vario Box Body / Estate (6K5)
View more
DIY rear axle restoration | Drivetrain restoration – Part 2
5 Essential Tips for beginner drivers: Avoid Common Mistakes
Transform Your Car's Look: 6 Simple Accessories You Need to Try!
5 possible reasons why your car heater isn't working
Most commonly replaced car parts on SEAT CORDOBA
Time to replace parts? Get even better deals in our Shop app.

SCAN ME




























