
Disclaimer
How to change track rod end on CITROËN C1 II (PA_, PS_) – replacement guide
downloads:
1
Views:
11
Important!
This replacement procedure can be used for:
CITROËN C1 II (PA_, PS_) 1.0 VTi, CITROËN C1 II (PA_, PS_) 1.2 VTi, CITROËN C1 II (PA_, PS_) 1.0 VTi … View more
The steps may slightly vary depending on the car design.
CITROËN C1 II (PA_, PS_) 1.0 VTi, CITROËN C1 II (PA_, PS_) 1.2 VTi, CITROËN C1 II (PA_, PS_) 1.0 VTi … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Track Rod End for C1 II (PA_, PS_) and other CITROËN models
Track rod end
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #17
Combination spanner #19
Drive socket # 17
Drive socket # 19
Wheel impact socket #17
Ratchet wrench
Torque wrench
Flat Screwdriver
Round-nose pliers
Nippers
Tap wrench
Vernier caliper
Crow bar
Ball joint puller
Wheel chock
Replacement: track rod end – CITROËN C1 II. AUTODOC recommends:
- Replace tie rod ends in pairs.
- The replacement procedure is identical for the right and left tie rod ends.
- All work should be done with the engine stopped.
Replacement: track rod end – CITROËN C1 II. Take the following steps:
- Step 1Secure the wheels with chocks.
- Step 2Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 3Raise the front of the car and secure on supports.Step 4Unscrew the wheel bolts.Replacement: track rod end – CITROËN C1 II. Tip:To avoid injury, hold up the wheel when unscrewing the bolts.
- Step 5Remove the wheel.
- Step 6Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.
- Step 7Remove the cotter pin fixing the tie rod end fastening. Use a crowbar. Use a flat screwdriver. Use round-nose pliers.
- Step 8Remove the cotter pin. Use a crowbar. Use nippers.Step 9Unscrew the end fastening nut to the steering knuckle. Use a drive socket #17. Use a tap wrench.
- Step 10When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper.
- Step 11Loosen the lock nut securing the tie rod end to the tie rod. Use a combination spanner #19.
- Step 12Disconnect the tie rod end from the steering knuckle. Use a ball joint puller.
- Step 13Screw the end out of the tie rod.
- Step 14Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray.
- Step 15Screw on a new tie rod end.Replacement: track rod end – CITROËN C1 II. AUTODOC experts recommend:While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements.
- Step 16Connect the tie rod end to the steering knuckle.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the CITROËN C1 II (PA, PS) model
Popular maintenance tutorials for Citroen C1 2
Complete guides for changing the Tie rod end on different CITROËN C1 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your CITROËN C1 II (PA_, PS_)
View more
- Discover the 4 Key Reasons Your CHECK ENGINE Light Could Be On | AUTODOC Tips
- Top 5 Car Interior Cleaning Mistakes You Should Avoid | AUTODOC Tips
- Top 7 Manual Transmission Mistakes to Avoid | AUTODOC Tips
- The most common problems when buying a used car | AUTODOC
Most commonly replaced car parts on CITROËN C1
Time to replace parts? Get even better deals in our Shop app.

SCAN ME