How to change tailgate struts on Opel Meriva X03 – replacement guide
downloads:
6
Views:
69
0
Users voted – 0
Important!
This replacement procedure can be used for:
OPEL Meriva A (X03) 1.4 16V Twinport LPG (E75),
OPEL Meriva A (X03) 1.8 (E75),
OPEL Meriva A (X03) 1.7 DTI (E75),
OPEL Meriva A (X03) 1.6 (E75),
OPEL Meriva A (X03) 1.7 CDTI (E75),
OPEL Meriva A (X03) 1.4 16V Twinport (E75),
OPEL Meriva A (X03) 1.6 (E75),
OPEL Meriva A (X03) 1.3 CDTI (E75),
OPEL Meriva A (X03) 1.6 Turbo (E75),
OPEL Meriva A (X03) 1.7 CDTI (E75),
OPEL Meriva A (X03) 1.3 CDTI (E75)
…
View more
The steps may slightly vary depending on the car design.
How to change gas struts / tailgate struts on OPEL MERIVA A [TUTORIAL AUTODOC]
All the parts you need to replace – Tailgate Struts for Meriva A (X03) and other OPEL models
Replacement: tailgate struts – Opel Meriva X03. AUTODOC experts recommend:
Right and left gas struts of the boot lid should be replaced simultaneously.
The replacement procedure is identical for the right and left gas struts of the boot lid.
All work should be done with the engine stopped.
Replacement: tailgate struts – Opel Meriva X03. Use the following procedure:
Step 1
Open the boot lid.
Step 2
Support the boot lid. Use a hydraulic transmission jack.
Step 3
Release the circlip connecting the gas strut to the boot lid. Use a flat screwdriver.
Step 4
Release the circlip connecting the gas strut to the car body. Use a flat screwdriver.
Replacement: tailgate struts – Opel Meriva X03. Tip:
To avoid any injuries, be sure to hold the boot lid while demounting the gas struts.
Step 5
Remove the boot lid gas strut.
Step 6
Clean the mounting seats of the boot strut. Use WD-40 spray.
Step 7
Install the new boot lid gas strut.
Replacement: tailgate struts – Opel Meriva X03. Tip from AUTODOC experts:
To avoid any injuries, be sure to hold the boot lid while installing the gas strut.
Step 8
Snap on the circlip connecting the gas strut to the car body.
Step 9
Snap on the circlip connecting the gas strut to the boot lid.
Step 10
Release the circlip connecting the gas strut to the car body. Use a flat screwdriver.
Step 11
Release the circlip connecting the gas strut to the boot lid. Use a flat screwdriver.
Replacement: tailgate struts – Opel Meriva X03. Professionals recommend:
To avoid any injuries, be sure to hold the boot lid while demounting the gas struts.
Step 12
Remove the boot lid gas strut.
Step 13
Clean the mounting seats of the boot strut. Use WD-40 spray.
Step 14
Install the new boot lid gas strut.
Replacement: tailgate struts – Opel Meriva X03. Tip from AUTODOC:
To avoid any injuries, be sure to hold the boot lid while installing the gas strut.
Step 15
Snap on the circlip connecting the gas strut to the car body.
Step 16
Snap on the circlip connecting the gas strut to the boot lid.
Step 17
Remove the hydraulic transmission jack.
AUTODOC recommends:
Replacement: tailgate struts – Opel Meriva X03. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.Check the working condition of the boot lid gas springs after they are installed.
Step 18
Close the lid of the luggage compartment.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the OPEL Meriva A (X03) model