Recommended replacement interval for the part category Spark plug : 18 month / 30000 km

Important!

This replacement procedure can be used for:
PEUGEOT PARTNER Platform/Chassis 1.6 … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Spark Plug for PARTNER Platform/Chassis and other PEUGEOT models

Alternative products

Spark plug

Replacement: spark plugs – PEUGEOT PARTNER Platform/Chassis. Tools you'll need:

                      High-temperature anti-seize lubricant
                    
                      Torx bit T20
                    
                      Torx bit T27
                    
                      Spark plug socket # 16
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Flat Screwdriver
                    
                      Crow bar
                    
                      Fender cover

Buy tools

Replacement: spark plugs – PEUGEOT PARTNER Platform/Chassis. Tip from AUTODOC experts:

The replacement procedure is the same for all spark plugs.
Please note: all work on the car – PEUGEOT PARTNER Platform/Chassis – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Open the hood.

Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 3

Unscrew the engine cover fastener. Use Torx T20.
Step 4

Remove the engine cover.

Replacement: spark plugs – PEUGEOT PARTNER Platform/Chassis. AUTODOC recommends:
Raise the engine cover, holding it on two sides simultaneously.
Step 5

Remove the crankcase ventilation hoses.
Step 6

Detach the connector from the ignition coil.
Step 7

Unscrew the ignition coil bracket. Use Torx T27.
Step 8

Pry up the ignition coil. Use a crowbar.
Step 9

Take out the ignition coil from the spark plug well.
Step 10

Clean dirt, dust and debris from inside the spark plug wells.
Step 11

Unscrew the spark plugs. Use the spark plug socket #16. Use a ratchet wrench.
Step 12

Take out the spark plugs.
Step 13

Apply a thin layer of a special high temperature anti-seize lubricant to the threads of the new spark plugs.
Step 14

Install the new spark plugs into their mounting seats. Use the spark plug socket #16.
Step 15

Screw new spark plugs and tighten them. Use the spark plug socket #16. Use a torque wrench. Tighten it to 26 nm torque.

Replacement: spark plugs – PEUGEOT PARTNER Platform/Chassis. Professionals recommend:
Don't tighten the plugs with excessive force. Exceeding tightening torque can damage the thread connection. Be careful when working with a spark plug wrench. Its skewing can cause damage to the threaded connection.
Step 16

Treat the ignition coil tips. Use high-temperature grease. Use a flat screwdriver.
Step 17

Plug in the ignition coil connector.
Step 18

Install the ignition coils to the spark plug wells. Make sure you hear a click indicating that it is locked in place.
Step 19

Tighten the fasteners of the ignition coils. Use Torx T20. Use a torque wrench. Tighten it to 8 nm torque.
Step 20

Install the crankcase ventilation hoses.
Step 21

Install the engine cover and secure it. Screw in the engine cover fasteners. Use Torx T20.

AUTODOC recommends:
Make sure the engine cover is properly seated. It should not be displaced with respect to the guiding fasteners and the throttle body air intake hose.Replacement: spark plugs – PEUGEOT PARTNER Platform/Chassis. Do not use excessive force during installation. This may damage the fasteners.
Step 22

Run the engine for a few minutes. This is necessary in order to make sure that the component operates properly.

Step 23

Shut off the engine.

Step 24

Remove the fender protection cover.

Step 25

Close the hood.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the PEUGEOT Partner I Platform / Chassis model

PEUGEOT PARTNER Platform/Chassis tyre size

How to change rear brake pads on PEUGEOT Partner I Platform / Chassis – replacement guide

Free download PDF
2.47 MB
How to change front brake pads on PEUGEOT PARTNER Platform/Chassis – replacement guide

Free download PDF
1.43 MB
How to change front brake discs on PEUGEOT PARTNER Platform/Chassis – replacement guide

Free download PDF
2.3 MB
How to change rear wheel bearing on PEUGEOT PARTNER Platform/Chassis – replacement guide

Free download PDF
2.03 MB
How to change front wheel bearing on PEUGEOT PARTNER Platform/Chassis – replacement guide

Free download PDF
3.66 MB
How to change front anti roll bar links on PEUGEOT Partner I Platform / Chassis – replacement guide

Free download PDF
1.33 MB

How to change spark plugs on PEUGEOT PARTNER Box – replacement guide

Free download PDF
1.17 MB
How to change spark plugs on PEUGEOT PARTNER Tepee – replacement guide

Free download PDF
1.17 MB
How to change spark plugs on PEUGEOT PARTNER Box (5) – replacement guide

Free download PDF
1.4 MB
How to change spark plugs on PEUGEOT PARTNER Combispace (5F) – replacement guide

Free download PDF
1013.76 KB
How to change spark plugs on PEUGEOT Partner Origin Van (G_) – replacement guide

Free download PDF
1.4 MB
How to change spark plugs on PEUGEOT Partner Origin Combispace (G_) – replacement guide

Free download PDF
1.4 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

5 Essential Tips for beginner drivers: Avoid Common Mistakes

4K views

Published on: 31/01/2023
5 Essential Tips to Prepare Your Car for Winter | AUTODOC tips

6K views

Published on: 05/02/2024
Stop Rust Before It Starts: Top 5 Tips for Car Body Protection | AUTODOC Insights

7K views

Published on: 27/07/2023
The most common problems when buying a used car | AUTODOC

4K views

Published on: 10/11/2022