Disclaimer
How to change spark plugs on BMW 1 Convertible (E88) – replacement guide
downloads:
12
Views:
228
Recommended replacement interval for the part category Spark plug : 18 month / 30000 km
Important!
This replacement procedure can be used for:
BMW 1 Convertible (E88) 118 i, BMW 1 Convertible (E88) 120 i … View more
The steps may slightly vary depending on the car design.
BMW 1 Convertible (E88) 118 i, BMW 1 Convertible (E88) 120 i … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Spark Plug for 1 Convertible (E88) and other BMW models
Alternative products

Electronic spray
High-temperature anti-seize lubricant
Torx bit T20
Spark plug socket # 16
Ratchet wrench
Torque wrench
Telescoping magnet
Crow bar
Fender cover
Replacement: spark plugs – BMW 1 Convertible (E88). Professionals recommend:
- The replacement procedure is the same for all spark plugs.
- Warning! Shut down the engine before starting any work – BMW 1 Convertible (E88).
Carry out replacement in the following order:
- Step 1Open the hood.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3
Unscrew the fasteners of the cabin filter housing cover. - Step 4.1
Raise a little the cabin filter housing cover.Step 4.2
Remove the cabin filter.Replacement: spark plugs – BMW 1 Convertible (E88). AUTODOC experts recommend:To avoid damaging the cabin filter cover, do not remove it before removing the filtering element. - Step 5
Remove the rubber strip. - Step 6
Remove the cabin filter housing cover. - Step 7
Disconnect the wiring harness from the cabin filter housing. - Step 8
Unscrew the filter housing fastening bolts. Use Torx T20. Use a ratchet wrench. - Step 9
Remove the cabin air filter housing. - Step 10
Unscrew the oil filler plug. - Step 11
Remove the engine cover. - Step 12
Tighten the oil filler cap. - Step 13
Unplug the connectors from the ignition coils. - Step 14
Take out the ignition coil from the spark plug well. Use a crowbar.Replacement: spark plugs – BMW 1 Convertible (E88). Tip:Remember the sequence of steps for ignition coil demounting. - Step 15
Clean dirt, dust and debris from inside the spark plug wells. - Step 16
Unscrew the spark plugs. Use the spark plug socket #16. Use a ratchet wrench. - Step 17
Take out the spark plugs. Use a telescoping magnet. - Step 18
Apply a thin layer of a special high temperature anti-seize lubricant to the threads of the new spark plugs. Treat the surface of the terminals of the new spark plugs. Use high-temperature grease. - Step 19
Install the new spark plugs into their mounting seats. - Step 20
Screw new spark plugs and tighten them. Use the spark plug socket #16. Use a torque wrench. Tighten it to 27 nm torque.Replacement: spark plugs – BMW 1 Convertible (E88). Tip from AUTODOC experts:Don't tighten the plugs with excessive force. Exceeding tightening torque can damage the thread connection. Be careful when working with a spark plug wrench. Its skewing can cause damage to the threaded connection.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the BMW 1 Convertible (E88) model
Popular maintenance tutorials for BMW E88
Complete guides for changing the Engine spark plug on different BMW 1 SERIES models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your BMW 1 Convertible (E88)
View more
7 signs of faulty fuel injectors | AUTODOC tips
Top 5 reasons why the suspension knocks | AUTODOC tips
Top 5 brake repair mistakes | AUTODOC tips
DIY engine block coffee table
Most commonly replaced car parts on BMW 1 SERIES
Time to replace parts? Get even better deals in our Shop app.

SCAN ME




























