Replacement: spark plugs – Audi A4 B8. AUTODOC experts recommend:
The replacement procedure is the same for all spark plugs.
Please note: all work on the car – Audi A4 B8 – should be done with the engine switched off.
Replacement: spark plugs – Audi A4 B8. Take the following steps:
Step 1
Open the hood.
Step 2
Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
Step 3
Remove the engine cover.
Replacement: spark plugs – Audi A4 B8. Tip:
Raise the engine cover, holding it on two sides simultaneously.Do not apply excessive force when removing the part. Otherwise you may damage it.
Step 4
Unscrew the fasteners of the ignition coil harness retainer. Use Torx T30. Use a ratchet wrench.
Step 5
Unplug the connectors from the ignition coils.
Step 6
Take out the ignition coils from the spark plug wells.
Replacement: spark plugs – Audi A4 B8. AUTODOC recommends:
Remember the sequence of steps for ignition coil demounting.
Step 7
Clean dirt, dust and debris from inside the spark plug wells.
Step 8
Unscrew the spark plugs. Use the spark plug socket #16. Use a ratchet wrench.
Step 9
Take out the spark plugs. Use a telescoping magnet.
Step 10
Apply a thin layer of a special high temperature anti-seize lubricant to the threads of the new spark plugs.
Step 11
Install the new spark plugs into their mounting seats. Use the spark plug socket #16.
Step 12
Screw new spark plugs and tighten them. Use the spark plug socket #16. Use a torque wrench. Tighten it to 27 nm torque.
Replacement: spark plugs – Audi A4 B8. AUTODOC experts recommend:
Don't tighten the plugs with excessive force. Exceeding tightening torque can damage the thread connection. Be careful when working with a spark plug wrench. Its skewing can cause damage to the threaded connection.
Step 13
Install the ignition coils to the spark plug wells. Make sure you hear a click indicating that it is locked in place.
AUTODOC recommends:
Replacement: spark plugs – Audi A4 B8. Follow the installation steps.
Step 14
Plug in the connectors of the ignition coils.
Step 15
Screw in the fasteners of the ignition coil harness retainer. Use Torx T30. Use a ratchet wrench.
Step 16
Install the engine cover and secure it.
Replacement: spark plugs – Audi A4 B8. Tip from AUTODOC experts:
Make sure the engine cover is properly seated. It should not be displaced with respect to the guiding fasteners.Do not apply excessive force when installing the part. Otherwise you may damage the fasteners.
Step 17
Remove the fender protection cover.
Step 18
Close the hood.
Step 19
Run the engine for a few minutes. This is necessary in order to make sure that the component operates properly.
Step 20
Shut off the engine.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the AUDI A4 B8 Saloon (8K2) model.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- scan the QR code
- download from App Store
- download from Google Play
Tips & tricks for your AUDI A4 Saloon (8K2, B8)
View more
Don’t Replace, Just Polish! Headlight Restoration with AUTODOC
Initial Car Inspection: What to Check Before You Buy | AUTODOC tips
DIY car soundproofing | AUTODOC tips
#DIY Guide: How to Fix a Cracked Windscreen Without a Garage Visit