How to change rear brake pads on Audi A4 B8 – replacement guide
AUDI A4 Saloon (8K2, B8) 2.0 TFSI quattro, AUDI A4 Saloon (8K2, B8) 3.0 TFSI quattro, AUDI A4 Saloon (8K2, B8) 3.0 TDI quattro, AUDI A4 Saloon (8K2, B8) 2.7 TDI, AUDI A4 Saloon (8K2, B8) 2.0 TFSI, AUDI A4 Saloon (8K2, B8) 2.0 TFSI, AUDI A4 Saloon (8K2, B8) S4 quattro, AUDI A4 Saloon (8K2, B8) 3.0 TDI quattro, AUDI A4 Saloon (8K2, B8) 2.0 TFSI flexible fuel quattro, AUDI A4 Saloon (8K2, B8) 2.0 TFSI quattro, AUDI A4 Saloon (8K2, B8) 2.0 TFSI, AUDI A4 Saloon (8K2, B8) 2.0 TDI, AUDI A4 Saloon (8K2, B8) 2.0 TDI quattro, AUDI A4 Saloon (8K2, B8) 2.0 TDI, AUDI A4 Saloon (8K2, B8) 2.0 TDI quattro, AUDI A4 Saloon (8K2, B8) 2.0 TFSI flexible fuel, AUDI A4 Saloon (8K2, B8) 2.0 TFSI quattro, AUDI A4 Saloon (8K2, B8) 2.0 TFSI, AUDI A4 Saloon (8K2, B8) 2.0 TFSI Flexfuel quattro, AUDI A4 Saloon (8K2, B8) 2.0 TFSI Flexfuel quattro … View more
The steps may slightly vary depending on the car design.
How to change rear brake pads on AUDI A4 B8 Saloon [TUTORIAL AUTODOC]


- Perform the replacement of brake pads in complete set for each axis. This provides effective braking.
- The replacement procedure is identical for all brake pads on the same axle.
- Warning! Shut down the engine before starting any work – Audi A4 B8.
- Step 1

Open the bonnet. Unscrew the brake fluid reservoir cap.
- Step 2

Put the parking brake system into service mode.
- Step 3

Secure the wheels with chocks.
- Step 4

Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 5

Raise the rear of the car and secure on supports.
- Step 6

Unscrew the wheel bolts.
AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. Audi A4 B8
- Step 7

Remove the wheel.
- Step 8

Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
- Step 9

Unscrew the brake caliper fastening. Use a combination spanner #15. Use a drive socket #13. Use a ratchet wrench.
- Step 10

Spread the brake pads. Use a crowbar.
- Step 11

Remove the brake caliper.
Replacement: brake pads – Audi A4 B8. AUTODOC recommends:Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
- Step 12

Remove the brake pads.
Replacement: brake pads – Audi A4 B8. Tip from AUTODOC:Measure the brake disc thickness. Upon reaching the wear limit the part must be replaced.
- Step 13

Treat the brake caliper piston. Use a nylon cleaning brush. Use a brake cleaner.
AUTODOC recommends:Replacement: brake pads – Audi A4 B8. After applying the spray, wait a few minutes.
- Step 14

Press in the brake caliper piston. Use brake caliper wind back tool.
- Step 15

Remove the retaining springs of the brake pads.
- Step 16

Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.
Replacement: brake pads – Audi A4 B8. Tip:After applying the spray, wait a few minutes.
- Step 17

Install the retaining springs of the brake pads.
Find out which tyre and wheel sizes are compatible with the AUDI A4 B8 Saloon (8K2) model
Popular maintenance tutorials for Audi A4 B8
Complete guides for changing the Brake pad set on different AUDI A4 models
Track expenses, manage logs, schedule replacements, and more.
DIY jack restoration | AUTODOC tips
Motorcycle fuel tank restoration
Why Checking Your Oil is Crucial for Engine Performance
What to do if your car’s bonnet won’t open | AUTODOC tips
Most commonly replaced car parts on AUDI A4




































