Disclaimer
How to change serpentine belt on RENAULT Master II Platform/Chassis – replacement guide
downloads:
0
Views:
6
Recommended replacement interval for the part category V-Ribbed Belt Set : 5 year / 120000 km
Important!
This replacement procedure can be used for:
RENAULT MASTER II Platform/Chassis (ED/HD/UD) 2.5 dCi, RENAULT MASTER II Platform/Chassis (ED/HD/UD) 2.2 dCI … View more
The steps may slightly vary depending on the car design.
RENAULT MASTER II Platform/Chassis (ED/HD/UD) 2.5 dCi, RENAULT MASTER II Platform/Chassis (ED/HD/UD) 2.2 dCI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Poly V-Belt for MASTER II Platform/Chassis (ED/HD/UD) and other RENAULT models
Alternative products
V-Ribbed Belt Set
Wire brush
WD-40 spray
All-purpose cleaning spray
Ceramic grease
Torque wrench
13 mm combination spanner
13 mm socket
24 mm wheel impact socket
Ratchet wrench or power tool for removal/installation of threaded fasteners
U-joint socket extension
Tommy bar
Pin punch
Long nose pliers
Car lift or jack with jack stands, and wheel chocks
Replacement: serpentine belt – RENAULT MASTER II Platform/Chassis (ED/HD/UD). AUTODOC experts recommend:
- All the work should be carried out with the ignition switched off.
Carry out the replacement steps as follows:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel fasteners. Use a 24 mm wheel impact socket. Use a tommy bar. - Step 3Raise the vehicle.Warning!If you are using a jack, make sure the car is parked on a hard, flat surface.Make sure to additionally secure the car with jack stands.Step 4
Unscrew the wheel fasteners.Replacement: serpentine belt – RENAULT MASTER II Platform/Chassis (ED/HD/UD). Tip:To avoid injury, hold up the wheel when unscrewing the fasteners. - Step 5
Remove the wheel. - Step 6
Move the belt tensioner pulley away from the V-ribbed belt. Use a 13 mm combination spanner. - Step 7
Secure the tensioner pulley in this position. Use a pin punch. - Step 8
Remove the V-ribbed belt. - Step 9
Clean the tensioner fasteners. Use a wire brush. Use WD-40 spray. - Step 10
Clean the idler pulley fastener. Use a wire brush. Use WD-40 spray. - Step 11
Unscrew the idler pulley fastener. Use a 13 mm socket. Use a ratchet wrench. Use a U-joint socket extension. - Step 12
Remove the fastening bolt. - Step 13
Remove the idler pulley. - Step 14
Unscrew the tensioner fasteners. Use a 13 mm socket. Use a ratchet wrench. Use a U-joint socket extension. - Step 15
Remove the fastening bolts. - Step 16
Remove the tensioner. - Step 17
Clean the tensioner mounting seats. Use a wire brush. Use an all-purpose cleaning spray. - Step 18
Install a new tensioner. - Step 19
Install the fastening bolts.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the RENAULT Master II Platform/Chassis model
Popular maintenance tutorials for Renault Master 2 Platform
Free download PDF
983.04 KB
Free download PDF1.08 MB
Free download PDF1.32 MB
Free download PDF1.67 MB
Free download PDF6.45 MB
Free download PDF2.44 MB
Complete guides for changing the Alternator belt on different RENAULT MASTER models
Free download PDF2.15 MB
Free download PDF2.07 MB
Free download PDF1.51 MB
Free download PDF1.84 MB
Free download PDF1.38 MB
Free download PDF1.96 MB
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your RENAULT MASTER II Platform/Chassis (ED/HD/UD)
View more
DIY starter repair | AUTODOC tips
BMW E30 Turbo Suspension Swap: Boost Your Handling | AUTODOC project
5 most common causes of oil leaks | AUTODOC tips
DIY brake caliper restoration | AUTODOC tips
Most commonly replaced car parts on RENAULT MASTER
Time to replace parts? Get even better deals in our Shop app.
SCAN ME