
Disclaimer
How to change serpentine belt on Opel Vivaro A van – replacement guide
downloads:
0
Views:
1
Recommended replacement interval for the part category V-Ribbed Belt Set : 6 year / 120000 km
Important!
This replacement procedure can be used for:
OPEL Vivaro A Combi (X83) 2.5 CDTI (F7, J7, A07), OPEL Vivaro A Combi (X83) 2.5 CDTI (F7, J7, A07) … View more
The steps may slightly vary depending on the car design.
OPEL Vivaro A Combi (X83) 2.5 CDTI (F7, J7, A07), OPEL Vivaro A Combi (X83) 2.5 CDTI (F7, J7, A07) … View more
The steps may slightly vary depending on the car design.
How to install new poly-V belt kit on the OPEL VIVARO A Van [AUTODOC TUTORIAL]

All the parts you need to replace – Poly V-Belt for Vivaro A Combi (X83) and other OPEL models
Alternative products

Wire brush
WD-40 spray
All-purpose cleaning spray
Ceramic grease
Torque wrench
13 mm offset ring spanner
10 mm socket
13 mm socket
T30 Torx screwdriver
19 mm wheel impact socket
Ratchet wrench or power tool for removal/installation of threaded fasteners
Tommy bar
Clip removal tool
Long nose pliers
Car lift or jack with jack stands, and wheel chocks
Replacement: serpentine belt – Opel Vivaro A van. AUTODOC recommends:
- All the work should be carried out with the ignition switched off.
Replacement: serpentine belt – Opel Vivaro A van. Recommended sequence of steps:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel fasteners. Use a 19 mm wheel impact socket. Use a tommy bar. - Step 3
Raise the vehicle.Replacement: serpentine belt – Opel Vivaro A van. Tip from AUTODOC:If you are using a jack, make sure the car is parked on a hard, flat surface.Make sure to additionally secure the car with jack stands. - Step 4
Unscrew the wheel fasteners.Caution!To avoid injury, hold up the wheel when unscrewing the fasteners. - Step 5
Remove the wheel. - Step 6
Unscrew the fasteners of the front part of the wheel arch liner. Use a T30 Torx screwdriver. - Step 7
Remove the clips from the front part of the wheel arch liner. Use a clip removal tool. - Step 8
Remove the front part of the wheel arch liner. - Step 9
Move the belt tensioner pulley away from the V-ribbed belt. Use a 13 mm offset ring spanner. - Step 10
Remove the V-ribbed belt. - Step 11
Unscrew the idler pulley fastener. Use a 13 mm offset ring spanner. - Step 12
Remove the fastening bolt. - Step 13
Remove the idler pulley. - Step 14
Clean the tensioner fasteners. Use a wire brush. Use WD-40 spray. - Step 15
Unscrew the tensioner fasteners. Use a 10 mm socket. Use a ratchet wrench. - Step 16
Remove the fastening bolts. - Step 17
Remove the tensioner. - Step 18
Clean the tensioner mounting seats. Use a wire brush. Use an all-purpose cleaning spray. - Step 19
Install a new tensioner. - Step 20
Install the fastening bolts. - Step 21
Tighten the tensioner fasteners. Use a 10 mm socket. Use a torque wrench. Tightening torque: 21 N·m. - Step 22
Install a new idler pulley.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the OPEL Vivaro A Combi (X83) model
Popular maintenance tutorials for Opel Vivaro A Combi
Complete guides for changing the Alternator belt on different OPEL VIVARO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your OPEL Vivaro A Combi (X83)
View more
Regain Your Confidence on the Road: Easy Headlight Restoration Tips
DIY vehicle AC compressor restoration
Top 7 signs of a bad starter
5 tools that make car repair incredibly simple | AUTODOC tips
Most commonly replaced car parts on OPEL VIVARO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME


































