Important!
This replacement procedure can be used for:
BMW 3 Touring (E36) 325 tds View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Engine Mount for 3 Touring (E36) and other BMW models
How to change Engine mount on BMW E36 Touring 320 i – step-by-step instructions for straightforward car repair
Engine mount
How to change Holder, engine mounting on BMW E36 Touring 320 i – step-by-step instructions for straightforward car repair
Holder, engine mounting
How to change Engine mount on BMW E36 Touring 320 i – step-by-step instructions for straightforward car repair
Engine mount
How to change Engine Transverse Strut on BMW E36 Touring 320 i – step-by-step instructions for straightforward car repair
Engine Transverse Strut
Tools
Replacement: engine mounts – BMW 3 Touring (E36). Tools you need:
Wire brush
WD-40 spray
Copper grease
HEX bit No.H5.
Drive socket # 16
Wheel impact socket #17
Ratchet wrench
Torque wrench
Crow bar
Fender cover
Hydraulic transmission jack
Wheel chock
Replacement: engine mounts – BMW 3 Touring (E36). AUTODOC experts recommend:
  • All work should be done with the engine stopped.
Carry out replacement in the following order:
  1. Step 1
    Open the bonnet.
    Step 2
    Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
    Step 3
    How to change Engine Mount on BMW E36 Touring 1995 - free PDF and video manuals
    Secure the wheels with chocks.
  2. Step 4
    How to replace BMW 3 Touring (E36) 320 i 1996 Engine Mount - step-by-step manuals and video guides
    Loosen the wheel mounting bolts. Use wheel impact socket #17.
  3. Step 5
    Lift the car using a jack or place it over an inspection pit.
    Step 6
    BMW E36 Touring 328 i 1997 Engine Mount replacement: free workshop manuals
    Unscrew the wheel bolts.
    Replacement: engine mounts – BMW 3 Touring (E36). AUTODOC recommends:
    To avoid injury, hold up the wheel when unscrewing the bolts.
  4. Step 7
    Changing Engine Mount on BMW 3 Touring (E36) 318 i 1998 by yourself
    Remove the wheel.
  5. Step 8
    How to remove BMW 3 SERIES 325 tds 1999 Engine Mount - online easy-to-follow instructions
    Detach the vacuum hose from the engine mount.
  6. Step 9
    How to replace Engine Mount on BMW 3 Touring (E36) 1995: download PDF manuals and video instructions
    Treat the lower fastener of the engine mount. Use WD-40 spray.
  7. Step 10
    How hard is it to do yourself: Engine Mount replacement on BMW E36 Touring 318 tds 1996 - download illustrated guide
    Unscrew the lower fastener of the engine mount. Use a drive socket #16.
  8. Step 11
    Need to know how to renew Engine Mount on BMW 3 SERIES 1997? This free workshop manual will help you to do it yourself
    Loosen the air intake fastening. Use HEX No.H5. Use a ratchet wrench.
  9. Step 12
    Changing of Engine Mount on BMW E36 Touring 1998 won't be an issue if you follow this illustrated step-by-step guide
    Detach the air duct housing from the air filter housing.
  10. Step 13
    BMW 3 SERIES 328 i Engine Mount replacement: online guides and video tutorials
    Unscrew the upper fastener of the engine mount. Use a drive socket #16. Use a ratchet wrench.
  11. Step 14
    Replacing Engine Mount on BMW E36 Touring 1995 320 i by yourself
    Support the engine in the oil pan area. Use a hydraulic transmission jack.
    Replacement: engine mounts – BMW 3 Touring (E36). Tip:
    Make sure that the engine is supported.
  12. Step 15
    3 Touring (E36) 325 tds 1996 Engine Mount DIY replacement workshop manual
    Remove the engine mount. Use a crowbar.
    Replacement: engine mounts – BMW 3 Touring (E36). AUTODOC experts recommend:
    Carefully check the other engine mounts and replace them if necessary.
  13. Step 16
    How to change Engine Mount on BMW 3 Touring (E36) 1997 - tips and tricks
    Install the engine mount to its mounting seat. Use a crowbar.
  14. Step 17
    Step-by-step recommendations for DIY replacement BMW E36 Touring 1998 325 tds Engine Mount
    Remove the support from under the engine.
    AUTODOC recommends:
    Replacement: engine mounts – BMW 3 Touring (E36). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
BMW 3 Touring (E36) Engine Mount replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
DIY BMW 3 Touring (E36) Engine Mount replacement - online guide
Tips & tricks for your BMW 3 Touring (E36)
View more
  • How to change Engine mounts on BMW 3 Touring (E36) 316 i - replacement tricks
    DIY brake caliper restoration | AUTODOC tips
  • Changing Engine mounting BMW E36 Touring 320 i - Replacement Tips
    TOP 6 WD-40 lifehacks | AUTODOC tips
  • Maintenance Hacks - BMW 3 Touring (E36) 328 i Motor mounts replacement guide
    TOP 5 mistakes when replacing shock absorbers | AUTODOC tips
  • Replace Motor mount on BMW E36 Touring - free video tips
    3 things to know before buying summer tyres | AUTODOC tips