Disclaimer
How to change rear wheel bearing on VOLVO S80 II (124) – replacement guide
downloads:
11
Views:
188
Important!
This replacement procedure can be used for:
VOLVO S80 II (124) T4, VOLVO S80 II (124) T5, VOLVO S80 II (124) D3 / D4, VOLVO S80 II (124) 3.2, VOLVO S80 II (124) 1.6 DRIVe, VOLVO S80 II (124) D5, VOLVO S80 II (124) T4F, VOLVO S80 II (124) D5, VOLVO S80 II (124) 2.5 T, VOLVO S80 II (124) 3.2, VOLVO S80 II (124) 2.4 D, VOLVO S80 II (124) T6 AWD, VOLVO S80 II (124) 2.5 T FlexFuel, VOLVO S80 II (124) 2.0 FlexFuel, VOLVO S80 II (124) 2.0 TDi, VOLVO S80 II (124) 2.5 T FlexFuel, VOLVO S80 II (124) 2.4 D, VOLVO S80 II (124) D5, VOLVO S80 II (124) 1.6 D DRIVe, VOLVO S80 II (124) 2.5 T, VOLVO S80 II (124) 2.0 T, VOLVO S80 II (124) 2.0 … View more
The steps may slightly vary depending on the car design.
VOLVO S80 II (124) T4, VOLVO S80 II (124) T5, VOLVO S80 II (124) D3 / D4, VOLVO S80 II (124) 3.2, VOLVO S80 II (124) 1.6 DRIVe, VOLVO S80 II (124) D5, VOLVO S80 II (124) T4F, VOLVO S80 II (124) D5, VOLVO S80 II (124) 2.5 T, VOLVO S80 II (124) 3.2, VOLVO S80 II (124) 2.4 D, VOLVO S80 II (124) T6 AWD, VOLVO S80 II (124) 2.5 T FlexFuel, VOLVO S80 II (124) 2.0 FlexFuel, VOLVO S80 II (124) 2.0 TDi, VOLVO S80 II (124) 2.5 T FlexFuel, VOLVO S80 II (124) 2.4 D, VOLVO S80 II (124) D5, VOLVO S80 II (124) 1.6 D DRIVe, VOLVO S80 II (124) 2.5 T, VOLVO S80 II (124) 2.0 T, VOLVO S80 II (124) 2.0 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Wheel Bearing for S80 II (124) and other VOLVO models
Alternative products

Wire brush
WD-40 spray
All-purpose cleaning spray
Brake cleaner
Ceramic grease
Torque wrench
Combination spanner #15
Drive socket # 13
Drive socket # 15
Torx bit T25
Torx bit T50
Torx bit T55
Wheel impact socket #19
Ratchet wrench
Tap wrench
Hammer
Impact screwdriver
Wheel chock
Replacement: wheel bearing – VOLVO S80 II (AS). AUTODOC recommends:
- Do not re-use the bearing assembly of your VOLVO S80 II (AS) car.
- The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
- All work should be done with the engine stopped.
Replacement: wheel bearing – VOLVO S80 II (AS). Use the following procedure:
- Step 1Secure the wheels with chocks.Step 2
Loosen the wheel bolts. Use wheel impact socket #19. Use a tap wrench. - Step 3Raise the car.AUTODOC recommends:If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.Step 4
Unscrew the wheel bolts.Replacement: wheel bearing – VOLVO S80 II (AS). Tip:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 5
Remove the wheel. - Step 6
Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the brake caliper fasteners. Use a combination spanner #15. Use a drive socket #13. Use a ratchet wrench. - Step 8
Remove the fastening bolts. - Step 9
Remove the brake caliper.Replacement: wheel bearing – VOLVO S80 II (AS). AUTODOC experts recommend:Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. - Step 10
Remove the brake pads. - Step 11
Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray. - Step 12
Unscrew the brake caliper bracket fasteners. Use a drive socket #15. Use a ratchet wrench. - Step 13
Remove the fastening bolts. - Step 14
Remove the brake caliper bracket. - Step 15
Clean the brake disc fastener. Use a wire brush. Use WD-40 spray. - Step 16
Unscrew the brake disc fasteners. Use Torx T50. Use an impact screwdriver. Use a hammer. - Step 17
Remove the fastening bolt. - Step 18
Remove the brake disc. - Step 19
Clean the wheel hub fasteners. Use a wire brush. Use WD-40 spray. - Step 20
Clean the ABS sensor fastener. Use a wire brush. Use WD-40 spray. - Step 21
Unscrew the ABS sensor fastener. Use Torx T25. Use a ratchet wrench. - Step 22
Disconnect the ABS sensor. - Step 23
Remove the fastening bolt. - Step 24
Clean the wheel hub fasteners. Use a wire brush. Use WD-40 spray. - Step 25
Unscrew the wheel hub fasteners. Use Torx T55. Use a ratchet wrench. - Step 26
Remove the fastening bolts. - Step 27
Remove the hub and the bearing together, since they are made as an assembly. - Step 28
Remove the brake disc cover. - Step 29
Clean the wheel hub mounting seat. Use a wire brush. - Step 30
Install the brake disc cover. - Step 31
Install the new wheel hub together with the bearing. - Step 32
Install the fastening bolts. - Step 33
Tighten the wheel hub fasteners. Use Torx T55. Use a torque wrench. Tighten it to 110 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VOLVO S80 II (AS, 124) model
Popular maintenance tutorials for Volvo S80 II
Complete guides for changing the Wheel bearings on different VOLVO S80 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VOLVO S80 II (124)
View more
Why Checking Your Oil is Crucial for Engine Performance
How to restore a steering wheel | AUTODOC tips
TOP 5 mistakes during DIY oil change | AUTODOC tips
Prevent Engine Damage: How to Identify Rocker Cover Gasket Issues and Proper Replacement | AUTODOC
Most commonly replaced car parts on VOLVO S80
ОЕ number
Time to replace parts? Get even better deals in our Shop app.

SCAN ME



































