
Disclaimer
How to change rear wheel bearing on RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) – replacement guide
downloads:
4
Views:
24
Important!
This replacement procedure can be used for:
RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.6, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 2.0, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.9 dCi, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 2.0 16V Turbo, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.9 dCi, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.9 dCi, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.5 dCi (EM1E), RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.6 16V, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.5 dCi (EM16), RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.6, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.9 dCi, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 2.0 (EM0S) … View more
The steps may slightly vary depending on the car design.
RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.6, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 2.0, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.9 dCi, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 2.0 16V Turbo, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.9 dCi, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.9 dCi, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.5 dCi (EM1E), RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.6 16V, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.5 dCi (EM16), RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.6, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 1.9 dCi, RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) 2.0 (EM0S) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Wheel Bearing for MEGANE II Coupé-Cabriolet (EM0/1_) and other RENAULT models
Wheel bearing kit
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Multipurpose grease
Copper grease
Combination spanner №15
Drive socket # 13
Drive socket # E16
Drive socket # 30
Wheel impact socket #19
Ratchet wrench
Torque wrench
Brake caliper wind back tool
Tap wrench
Hammer
Rubber mallet
Crow bar
Wheel chock
Replacement: wheel bearing – RENAULT MEGANE II Coupé-Cabriolet (EM0/1_). AUTODOC experts recommend:
- Do not re-use the bearing assembly of your RENAULT MEGANE II Coupé-Cabriolet (EM0/1_) car.
- The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
- All work should be done with the engine stopped.
Replacement: wheel bearing – RENAULT MEGANE II Coupé-Cabriolet (EM0/1_). Recommended sequence of steps:
- Step 1Open the bonnet. Unscrew the brake fluid reservoir cap.Step 2Secure the wheels with chocks.
- Step 3Loosen the wheel mounting bolts. Use wheel impact socket #19.
- Step 4Raise the rear of the car and secure on supports.Step 5Unscrew the wheel bolts.AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. RENAULT MEGANE II Coupé-Cabriolet (EM0/1_)
- Step 6Remove the wheel.
- Step 7Spread the brake pads. Use a crowbar.
- Step 8Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
- Step 9Unscrew the brake caliper fastening. Use a combination spanner #15. Use a drive socket #13. Use a ratchet wrench.
- Step 10Remove the brake caliper.Replacement: wheel bearing – RENAULT MEGANE II Coupé-Cabriolet (EM0/1_). AUTODOC recommends:Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
- Step 11Remove the brake pads. Use a crowbar.
- Step 12Clean the brake caliper bracket fasteners. Use WD-40 spray.
- Step 13Unscrew the caliper bracket fastening. Use a drive socket #E16. Use a tap wrench.
- Step 14Remove the caliper bracket.
- Step 15Pry up and remove the wheel hub cap. Use a crowbar. Use a hammer.
- Step 16Unscrew the hub lock nut. Use a drive socket #30. Use a tap wrench.
- Step 17Remove the brake disc assemled with the wheel hub bearing.
- Step 18Install the brake disc assembled with the wheel hub bearing.
- Step 19Screw the wheel hub lock nut. Use a drive socket #30. Use a torque wrench. Tighten it to 175 Nm torque.
- Step 20Treat the hub where it contacts the brake disk. Use a multipurpose grease.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the RENAULT Megane II Coupé-Cabriolet (EM) model
Popular maintenance tutorials for Megane 2 CC
Complete guides for changing the Wheel bearings on different RENAULT MEGANE models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your RENAULT MEGANE II Coupé-Cabriolet (EM0/1_)
View more
- 5 causes of turbocharger failure and how to avoid them
- How to choose the right engine oil for your car | AUTODOC
- Understanding Car Tools: The Key Differences You Need to Know | AUTODOC tips
- Extend your engine's life: Avoid these 3 damaging factors | AUTODOC tips
Most commonly replaced car parts on RENAULT MEGANE
Time to replace parts? Get even better deals in our Shop app.

SCAN ME