Important!

This replacement procedure can be used for:
DACIA SANDERO II 1.5 dCi 75 / Blue dCi 75 (B8JW, B8M4, B8AH, B8M7, B8M6), DACIA SANDERO II 1.2, DACIA SANDERO II 1.2 LPG, DACIA SANDERO II TCe 90 (B8M1, B8MA), DACIA SANDERO II 1.5 dCi, DACIA SANDERO II 1.5 dCi, DACIA SANDERO II 1.6, DACIA SANDERO II 1.2, DACIA SANDERO II TCe 90 LPG (B8M1), DACIA SANDERO II 1.0 SCe 75 (B8JC, B8JD), DACIA SANDERO II 1.5 Blue dCi 95 (B8JL), DACIA SANDERO II 1.0 TCe 100 (B8ML), DACIA SANDERO II 1.0 LPG (B8ML) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Wheel Bearing for SANDERO II and other DACIA models

Alternative products

Wheel bearing kit

Replacement: wheel bearing – DACIA SANDERO II. Tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Multipurpose grease
                    
                      Copper grease 
                    
                      Combination spanner №15
                    
                      Drive socket # 13 
                    
                      Drive socket # E16 
                    
                      Drive socket # 30 
                    
                      Wheel impact socket #19
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Brake caliper wind back tool
                    
                      Tap wrench
                    
                      Hammer
                    
                      Rubber mallet
                    
                      Crow bar
                    
                      Wheel chock

Buy tools

Replacement: wheel bearing – DACIA SANDERO II. AUTODOC experts recommend:

Do not re-use the bearing assembly of your DACIA SANDERO II car.
The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
All work should be done with the engine stopped.

Replacement: wheel bearing – DACIA SANDERO II. Recommended sequence of steps:

Step 1

Open the bonnet. Unscrew the brake fluid reservoir cap.

Step 2

Secure the wheels with chocks.
Step 3

Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 4

Raise the rear of the car and secure on supports.

Step 5

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. DACIA SANDERO II
Step 6

Remove the wheel.
Step 7

Spread the brake pads. Use a crowbar.
Step 8

Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
Step 9

Unscrew the brake caliper fastening. Use a combination spanner #15. Use a drive socket #13. Use a ratchet wrench.
Step 10

Remove the brake caliper.

Replacement: wheel bearing – DACIA SANDERO II. AUTODOC recommends:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
Step 11

Remove the brake pads. Use a crowbar.
Step 12

Clean the brake caliper bracket fasteners. Use WD-40 spray.
Step 13

Unscrew the caliper bracket fastening. Use a drive socket #E16. Use a tap wrench.
Step 14

Remove the caliper bracket.
Step 15

Pry up and remove the wheel hub cap. Use a crowbar. Use a hammer.
Step 16

Unscrew the hub lock nut. Use a drive socket #30. Use a tap wrench.
Step 17

Remove the brake disc assemled with the wheel hub bearing.
Step 18

Install the brake disc assembled with the wheel hub bearing.
Step 19

Screw the wheel hub lock nut. Use a drive socket #30. Use a torque wrench. Tighten it to 175 Nm torque.
Step 20

Treat the hub where it contacts the brake disk. Use a multipurpose grease.
Step 21

Install the cap of the hub nut. Use a rubber mallet.

Replacement: wheel bearing – DACIA SANDERO II. Tip:
The cap must always be replaced. When you install the previously used cap the sealing will be lost.
Step 22

Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.

AUTODOC recommends:
Replacement: wheel bearing – DACIA SANDERO II. After applying the spray, wait a few minutes.
Step 23

Install the brake caliper bracket.
Step 24

Tighten the brake caliper bracket. Use a drive socket #Е16. Use a torque wrench. Tighten it to 105 Nm torque.
Step 25

Press in the brake caliper piston. Use brake caliper wind back tool.
Step 26

Install the brake pads.
Step 27

Install the brake caliper and fix it. Use a combination spanner #15. Use a drive socket #13. Use a torque wrench. Tighten it to 35 Nm torque.

Replacement: wheel bearing – DACIA SANDERO II. Tip from AUTODOC:
Without starting the engine, press the brake pedal several times until you feel significant resistance.
Step 28

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 29

Clean the brake disk surface. Use a wire brush. Use a brake cleaner.

Replacement: wheel bearing – DACIA SANDERO II. Tip from AUTODOC experts:
After applying the spray, wait a few minutes.
Step 30

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. DACIA SANDERO II
Step 31

Screw in the wheel bolts. Use wheel impact socket #19.
Step 32

Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 110 Nm torque.
Step 33

Remove the jacks and chocks.

AUTODOC recommends:
Check the brake fluid level in the expansion tank and refill if necessary.
Step 34

Tighten the brake fluid reservoir cap. Close the hood.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the DACIA Sandero II model

Dacia Sandero Mk2 tyre size

How to change front wheel bearing on DACIA SANDERO II – replacement guide

Free download PDF
3.39 MB
How to change serpentine belt on DACIA SANDERO II – replacement guide

Free download PDF
1.62 MB
How to change spark plugs on DACIA SANDERO II – replacement guide

Free download PDF
880.64 KB
How to change engine oil and filter on DACIA SANDERO II – replacement guide

Free download PDF
1.17 MB
How to change fuel filter on DACIA SANDERO II – replacement guide

Free download PDF
962.56 KB
How to change pollen filter on DACIA SANDERO II – replacement guide

Free download PDF
634.88 KB

How to change front wheel bearing on DACIA SANDERO II – replacement guide

Free download PDF
3.39 MB
How to change front wheel bearing on DACIA SANDERO – replacement guide

Free download PDF
3.4 MB
How to change rear wheel bearing on DACIA SANDERO – replacement guide

Free download PDF
1.45 MB
How to change wheel bearing on a car – replacement tutorial

Universal

Free download PDF
2.41 MB
How to change rear wheel bearing on DACIA LOGAN MCV (KS_) – replacement guide

Free download PDF
1.24 MB
How to change rear wheel bearing on DACIA LOGAN (LS_) – replacement guide

Free download PDF
1.24 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

Top 5 Mistakes to Avoid for Safe Engine Bay Repairs | AUTODOC Tips

8K views

Published on: 04/08/2023
5 most common causes of oil leaks | AUTODOC tips

59K views

Published on: 30/03/2023
Top 5 car noises you shouldn't ignore

6K views

Published on: 10/04/2025
#TPMS Explained: Why Your Light is On and How to Respond Safely

8K views

Published on: 28/09/2023