Disclaimer
How to change rear wheel bearing on AUDI Q3 Sportback (F3N) – replacement guide
downloads:
2
Views:
16
Important!
This replacement procedure can be used for:
AUDI Q3 Sportback (F3N) 35 TFSI Mild Hybrid, AUDI Q3 Sportback (F3N) 35 TDI, AUDI Q3 Sportback (F3N) 35 TFSI … View more
The steps may slightly vary depending on the car design.
AUDI Q3 Sportback (F3N) 35 TFSI Mild Hybrid, AUDI Q3 Sportback (F3N) 35 TDI, AUDI Q3 Sportback (F3N) 35 TFSI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Wheel Bearing for Q3 Sportback (F3N) and other AUDI models
Alternative products

Wire brush
WD-40 spray
Multipurpose grease
Drive socket # 13
Combination spanner #13
Combination spanner #19
XZN socket bit # 12
XZN socket bit # 18
Torx bit T30
Wheel impact socket #17
Tap wrench
Ratchet wrench
Torque wrench
Crow bar
Rubber mallet
Wheel chock
Replacement: wheel bearing – AUDI Q3 Sportback (F3N). AUTODOC recommends:
- Do not re-use the bearing assembly of your AUDI Q3 Sportback (F3N) car.
- The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
- All work should be done with the engine stopped.
Replacement: wheel bearing – AUDI Q3 Sportback (F3N). Use the following procedure:
- Step 1
Secure the wheels with chocks. - Step 2Loosen the wheel mounting bolts. Use wheel impact socket #17.Step 3Raise the rear of the car and secure on supports.Step 4
Unscrew the wheel bolts.Replacement: wheel bearing – AUDI Q3 Sportback (F3N). Tip:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 5
Remove the wheel. - Step 6Spread the brake pads. Use a crowbar.Step 7
Unscrew the brake caliper fastening. Use a combination spanner #13. Use a combination spanner #19. - Step 8
Remove the brake caliper.Replacement: wheel bearing – AUDI Q3 Sportback (F3N). AUTODOC experts recommend:Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. - Step 9
Remove the brake pads. - Step 10
Treat the brake caliper bracket fasteners. Use WD-40 spray. - Step 11
Unscrew the caliper bracket fastening. Use XZN #12. Use a tap wrench. Use a ratchet wrench. - Step 12
Remove the caliper bracket. - Step 13
Unscrew the brake disc fastening. Use Torx T30. Use a ratchet wrench. - Step 14
Remove the brake disc. - Step 15
Remove the hub bearing protection cap. Use a crowbar. Use a rubber mallet. - Step 16
Unscrew the wheel hub axle nut. Use XZN #18. Use a tap wrench. - Step 17
Remove the hub and the bearing together, since they are a sealed unit. - Step 18
Clean the guiding part of the stub axle. Use WD-40 spray. - Step 19
Install the new wheel hub with a bearing.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the AUDI Q3 Sportback (F3N) model
Popular maintenance tutorials for AUDI Q3 Sportback (F3N)
Complete guides for changing the Wheel bearings on different AUDI Q3 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your AUDI Q3 Sportback (F3N)
View more
The Fast and Easy Way to Fix a Broken Wheel Stud | AUTODOC tips
The Ultimate Guide to Engine Bay Cleaning | AUTODOC
Top 5 reasons why your car squeals | AUTODOC Tips
5 mistakes when replacing consumables
Most commonly replaced car parts on AUDI Q3
Time to replace parts? Get even better deals in our Shop app.

SCAN ME



































