
Disclaimer
How to change rear strut mount on AUDI A3 Saloon (8VS, 8VM) – replacement guide
downloads:
6
Views:
32
Important!
This replacement procedure can be used for:
AUDI A3 Saloon (8VS, 8VM) 1.4 TFSI, AUDI A3 Saloon (8VS, 8VM) 2.0 TDI, AUDI A3 Saloon (8VS, 8VM) 1.2 TFSI, AUDI A3 Saloon (8VS, 8VM) 1.6 TDI, AUDI A3 Saloon (8VS, 8VM) 1.4 TFSI, AUDI A3 Saloon (8VS, 8VM) 1.4 TFSI, AUDI A3 Saloon (8VS, 8VM) 1.8 TFSI, AUDI A3 Saloon (8VS, 8VM) 2.0 TDI, AUDI A3 Saloon (8VS, 8VM) 2.0 TDI, AUDI A3 Saloon (8VS, 8VM) 2.0 TDI, AUDI A3 Saloon (8VS, 8VM) 1.8 TFSI, AUDI A3 Saloon (8VS, 8VM) 2.0 TDI, AUDI A3 Saloon (8VS, 8VM) 1.4 TSI, AUDI A3 Saloon (8VS, 8VM) 1.6 TDI … View more
The steps may slightly vary depending on the car design.
AUDI A3 Saloon (8VS, 8VM) 1.4 TFSI, AUDI A3 Saloon (8VS, 8VM) 2.0 TDI, AUDI A3 Saloon (8VS, 8VM) 1.2 TFSI, AUDI A3 Saloon (8VS, 8VM) 1.6 TDI, AUDI A3 Saloon (8VS, 8VM) 1.4 TFSI, AUDI A3 Saloon (8VS, 8VM) 1.4 TFSI, AUDI A3 Saloon (8VS, 8VM) 1.8 TFSI, AUDI A3 Saloon (8VS, 8VM) 2.0 TDI, AUDI A3 Saloon (8VS, 8VM) 2.0 TDI, AUDI A3 Saloon (8VS, 8VM) 2.0 TDI, AUDI A3 Saloon (8VS, 8VM) 1.8 TFSI, AUDI A3 Saloon (8VS, 8VM) 2.0 TDI, AUDI A3 Saloon (8VS, 8VM) 1.4 TSI, AUDI A3 Saloon (8VS, 8VM) 1.6 TDI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Strut Mount for A3 Saloon (8VS, 8VM) and other AUDI models
Top strut mount
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Ceramic grease
Copper grease
Torque wrench
Combination spanner #18
Drive socket # 13
Drive socket # 16
Drive socket # 18
Shock absorber socket DD#5,2
Shock absorber socket DD#6
Torx bit T25
Wheel impact socket #17
Ratchet wrench
Vice
Crow bar
Hydraulic transmission jack
Wheel chock
Replacement: strut mount – AUDI A3 Limousine (8VS). Tip from AUTODOC experts:
- The replacement procedure is identical for the mounts of the right and left shock absorbers of the rear suspension.
- Both mounts of the rear shock struts should be replaced simultaneously.
- Please note: all work on the car – AUDI A3 Limousine (8VS) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Secure the wheels with chocks.Step 2Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 3Raise the car.Replacement: strut mount – AUDI A3 Limousine (8VS). Tip from AUTODOC experts:If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.Step 4Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. AUDI A3 Limousine (8VS)
- Step 5Remove the wheel.
- Step 6Clean the lower shock absorber fastener. Use a wire brush. Use WD-40 spray.
- Step 7Support the rear knuckle. Use a hydraulic transmission jack.
- Step 8Unscrew the lower fastener of the shock absorber. Use a combination spanner #18. Use a drive socket #18. Use a ratchet wrench.
- Step 9Clean the locker fasteners. Use a wire brush.
- Step 10Unscrew the locker fasteners. Use Torx T25. Use a ratchet wrench.
- Step 11Move the locker aside to gain access to the upper shock absorber fasteners.
- Step 12Clean the charcoal canister fastener. Use a wire brush. Use WD-40 spray.
- Step 13Unscrew the charcoal canister fastener. Use a drive socket #13. Use a ratchet wrench.
- Step 14Move the charcoal canister aside to gain access to the upper shock absorber fasteners.
- Step 15Clean the fasteners of the shock absorber upper mount. Use a wire brush. Use WD-40 spray.
- Step 16Unscrew the shock absorber mount fasteners. Use a drive socket #16. Use a ratchet wrench.
- Step 17Remove the fastening bolts.
- Step 18Lower the hydraulic transmission jack by 10-15 cm.
- Step 19Remove the fastening bolt.
- Step 20Remove the shock absorber.
- Step 21Clean the shock absorber mounting seats. Use a wire brush. Use WD-40 spray.
- Step 22Grip the shock absorber in a vice.
- Step 23Remove the shock absorber mount cap. Use a crowbar.
- Step 24Clean the shock absorber rod fastener. Use a wire brush. Use WD-40 spray.
- Step 25Remove the fastener of the shock absorber piston rod. Use a drive socket #16. Use a shock absorber socket DD№5,2. Use a ratchet wrench.
- Step 26Remove the shock absorber mount, boot and bump stop.AUTODOC recommends:Replacement: strut mount – AUDI A3 Limousine (8VS). Carefully inspect the mount, the boot, and the bump stop of the shock absorber. Replace if necessary.
- Step 27Install the new mount, boot, and bump stop on the shock absorber.
- Step 28Tighten the shock absorber rod nut. Use a drive socket #16. Use a shock absorber socket DD№6. Use a torque wrench. Tighten it to 25 Nm torque.
- Step 29Treat the shock absorber rod fastener. Use copper grease.
- Step 30Install the shock absorber mount cap.
- Step 31Release the vice and take out the shock absorber.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the AUDI A3 Saloon (8VS, 8VM) model
Popular maintenance tutorials for Audi A3 Saloon
Complete guides for changing the Strut mount on different AUDI A3 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your AUDI A3 Saloon (8VS, 8VM)
View more
- Prevent Engine Damage: How to Identify Rocker Cover Gasket Issues and Proper Replacement | AUTODOC
- When, why, and how to change engine oil | AUTODOC tips
- Revitalize Your Car Interior: DIY Steering Wheel Cover with AUTODOC Tips
- How to make an injector test bench yourself
Most commonly replaced car parts on AUDI A3
Time to replace parts? Get even better deals in our Shop app.

SCAN ME