Disclaimer
How to change rear shock absorbers on AUDI A4 Convertible (8H7, B6, 8HE, B7) – replacement guide
downloads:
2
Views:
20
Important!
This replacement procedure can be used for:
AUDI A4 Convertible (8H7, B6, 8HE, B7) 2.4, AUDI A4 Convertible (8H7, B6, 8HE, B7) 3.0, AUDI A4 Convertible (8H7, B6, 8HE, B7) 2.4, AUDI A4 Convertible (8H7, B6, 8HE, B7) 2.5 TDI, AUDI A4 Convertible (8H7, B6, 8HE, B7) 1.8 T, AUDI A4 Convertible (8H7, B6, 8HE, B7) 1.8 T quattro, AUDI A4 Convertible (8H7, B6, 8HE, B7) 3.0 quattro, AUDI A4 Convertible (8H7, B6, 8HE, B7) 2.0, AUDI A4 Convertible (8H7, B6, 8HE, B7) 1.8 T, AUDI A4 Convertible (8H7, B6, 8HE, B7) 3.0 … View more
The steps may slightly vary depending on the car design.
AUDI A4 Convertible (8H7, B6, 8HE, B7) 2.4, AUDI A4 Convertible (8H7, B6, 8HE, B7) 3.0, AUDI A4 Convertible (8H7, B6, 8HE, B7) 2.4, AUDI A4 Convertible (8H7, B6, 8HE, B7) 2.5 TDI, AUDI A4 Convertible (8H7, B6, 8HE, B7) 1.8 T, AUDI A4 Convertible (8H7, B6, 8HE, B7) 1.8 T quattro, AUDI A4 Convertible (8H7, B6, 8HE, B7) 3.0 quattro, AUDI A4 Convertible (8H7, B6, 8HE, B7) 2.0, AUDI A4 Convertible (8H7, B6, 8HE, B7) 1.8 T, AUDI A4 Convertible (8H7, B6, 8HE, B7) 3.0 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Shock Absorber for A4 Convertible (8H7, B6, 8HE, B7) and other AUDI models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #21
Drive socket # 13
Drive socket # 16
Drive socket # 21
Torx bit T25
Wheel impact socket #17
Ratchet wrench
Torque wrench
Shock absorber socket №DD6
Vice
Crow bar
Hydraulic transmission jack
Wheel chock
Replacement: shock absorbers – AUDI A4 Convertible (8H7, B6, 8HE, B7). AUTODOC recommends:
- Both shock absorbers of the rear suspension should be replaced simultaneously.
- The replacement procedure is identical for the left and right shock absorbers of the rear suspension.
- All work should be done with the engine stopped.
Replacement: shock absorbers – AUDI A4 Convertible (8H7, B6, 8HE, B7). Use the following procedure:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the rear of the car and secure on supports.Step 4
Unscrew the wheel bolts.Replacement: shock absorbers – AUDI A4 Convertible (8H7, B6, 8HE, B7). AUTODOC experts recommend:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 5
Remove the wheel. - Step 6
Clean the shock absorber fasteners. Use a wire brush. Use WD-40 spray. - Step 7
Support the arm. Use a hydraulic transmission jack. - Step 8
Unscrew the lower fastener of the shock absorber. Use a combination spanner #21. Use a drive socket #21. Use a ratchet wrench. - Step 9
Remove the fastening bolt. - Step 10
Detach the lower part of the shock absorber. Use a crowbar. - Step 11
Unscrew and remove the wheel arch cover fasteners. Use Torx T25. - Step 12
Remove the wheel arch cover. - Step 13
Clean the shock absorber fasteners. Use a wire brush. Use WD-40 spray. - Step 14
Unscrew the upper fastener of the shock absorber. Use a drive socket #13. Use a ratchet wrench.AUTODOC recommends:Important! Hold the shock absorber while unscrewing the fastening bolts. AUDI A4 Convertible (8H7, B6, 8HE, B7) - Step 15
Remove the shock absorber. - Step 16
Grip the shock absorber in a vice. - Step 17
Clean the shock absorber rod fastener. Use a wire brush. Use WD-40 spray. - Step 18
Remove the shock absorber piston rod fastening. Use a shock absorber socket DD№6. Use a drive socket #16. Use a ratchet wrench. - Step 19
Remove the shock absorber mount, boot and bump stop.Replacement: shock absorbers – AUDI A4 Convertible (8H7, B6, 8HE, B7). Tip from AUTODOC:Examine the shock absorber dust cap and the bump stop. Replace them if necessary. Before installing a new shock absorber you should pump it manually 3-5 times. - Step 20
Install the mount, boot and bump stop onto a new shock absorber. - Step 21
Screw the shock strut piston rod upper fastening. Use a shock absorber socket DD№6. Use a drive socket #16. Use a torque wrench. Tighten it to 25 Nm torque. - Step 22
Release the vice and take out the shock absorber. - Step 23
Clean the shock absorber mounting seats. Use a wire brush. Use WD-40 spray. - Step 24
Place the shock absorber in the wheel arch and secure it.Replacement: shock absorbers – AUDI A4 Convertible (8H7, B6, 8HE, B7). Tip:To avoid injury, hold the shock absorber cautiously tight when screwing in the fastening bolts.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the AUDI A4 B6/B7 Convertible (8H7, 8HE) model
Popular maintenance tutorials for Audi A4 Convertible
Complete guides for changing the Shock absorbers on different AUDI A4 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your AUDI A4 Convertible (8H7, B6, 8HE, B7)
View more
Three ways to change oil without a lift
#DIY Wheel Rim Restoration: Revive Scratches and Chips Easily!
5 Essential Tips to Prepare Your Car for Winter | AUTODOC tips
5 tools that make car repair incredibly simple | AUTODOC tips
Most commonly replaced car parts on AUDI A4
Time to replace parts? Get even better deals in our Shop app.

SCAN ME


































