Disclaimer
How to change rear lower arm on ALPINA B7 (E65) – replacement guide
downloads:
1
Views:
10
Important!
This replacement procedure can be used for:
ALPINA B7 (E65) 4.4 … View more
The steps may slightly vary depending on the car design.
ALPINA B7 (E65) 4.4 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Control Arm for B7 (E65) and other ALPINA models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #18
Combination spanner #21
Drive socket # 10
Wheel impact socket #17
Ratchet wrench
Torque wrench
Flat Screwdriver
Crow bar
Hydraulic transmission jack
Wheel chock
Replacement: rear lower arm – ALPINA B7 (E65). Tip from AUTODOC experts:
- The replacement procedure is identical for the right and left upper control arms.
- Please note: all work on the car – ALPINA B7 (E65) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the rear of the car and secure on supports.Step 4
Unscrew the wheel bolts.Replacement: rear lower arm – ALPINA B7 (E65). Tip:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 5
Remove the wheel. - Step 6
Disconnect the ABS sensor wiring. Use a flat screwdriver. - Step 7
Disconnect the brake pad wear sensor cable. Use a flat screwdriver. - Step 8
Remove the mounting bracket of the ABS sensor wiring from the upper arm. Use a flat screwdriver. - Step 9Clean all joints of the arm. Use a wire brush. Use WD-40 spray.Step 10
Unscrew the front arm fastener. Use a combination spanner #18 (2 pieces). - Step 11
Remove the front fastener of the control arm. Use a crowbar. Use a flat screwdriver. - Step 12
Unscrew the fastener connecting the control arm to the rear knuckle. Use a combination spanner #21. Use a drive socket #10. Use a ratchet wrench. - Step 13
Detach the suspension arm from the rear knuckle. - Step 14
Remove the arm. - Step 15Clean the mounting seats and the thread of the suspension arm. Use a wire brush. Use WD-40 spray.Step 16
Install a new arm.Replacement: rear lower arm – ALPINA B7 (E65). AUTODOC recommends:During the installation process, use only new bolts and nuts.Do not damage the ball joint cover. - Step 17Attach the suspension arm to the rear knuckle.Step 18
Tighten the fastener connecting the suspension arm to the rear knuckle. Use a combination spanner #21. Use a drive socket #10. Use a torque wrench. Tighten it to 165 Nm torque. - Step 19
Install the front fastener of the arm.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the ALPINA B7 Saloon (E65) model
Popular maintenance tutorials for ALPINA B7 (E65)
Complete guides for changing the Control arm on different ALPINA B7 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your ALPINA B7 (E65)
View more
How to tighten cylinder head bolts
DIY car soundproofing | AUTODOC tips
TOP 8 mistakes car owners make | AUTODOC tips
Motorcycle fuel tank restoration
Most commonly replaced car parts on ALPINA B7
Time to replace parts? Get even better deals in our Shop app.

SCAN ME
























