Disclaimer
How to change rear coil springs on MERCEDES-BENZ E-Class Coupe (C124) – replacement guide
downloads:
0
Views:
3
Important!
This replacement procedure can be used for:
MERCEDES-BENZ E-Class Coupe (C124) E 320 (124.052), MERCEDES-BENZ E-Class Coupe (C124) E 220 (124.042), MERCEDES-BENZ E-Class Coupe (C124) E 200 (124.040) … View more
The steps may slightly vary depending on the car design.
MERCEDES-BENZ E-Class Coupe (C124) E 320 (124.052), MERCEDES-BENZ E-Class Coupe (C124) E 220 (124.042), MERCEDES-BENZ E-Class Coupe (C124) E 200 (124.040) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Springs for E-Class Coupe (C124) and other MERCEDES-BENZ models
Alternative products

Wire brush
WD-40 spray
All-purpose cleaning spray
Ceramic grease
Torque wrench
Combination spanner #13
Combination spanner #17
Combination spanner #19
Combination spanner #22
Drive socket # 13
Drive socket # 17
Drive socket # 19
Drive socket # 22
Shock absorber socket # 16
Shock absorber socket #DD5.2
Shock absorber socket #DD6
Wheel impact socket #17
Ratchet wrench
Tap wrench
Hammer
Pin punch
Crow bar
Hydraulic transmission jack
Wheel chock
Replacement: coil springs – MERCEDES-BENZ E-CLASS Coupe (C124). Tip from AUTODOC experts:
- Both coil springs of the rear suspension should be replaced simultaneously.
- The replacement procedure is identical for the left and right coil springs of the rear suspension.
- Warning! Shut down the engine before starting any work – MERCEDES-BENZ E-CLASS Coupe (C124).
Carry out replacement in the following order:
- Step 1Open the luggage compartment.Step 2
Remove the luggage compartment trim. - Step 3
Clean the upper fastener of the shock absorber. Use a wire brush. Use WD-40 spray. - Step 4
Loosen the upper fastener of the shock absorber. Use a combination spanner #17. Use a shock absorber socket #DD5.2. Use a ratchet wrench. - Step 5Secure the wheels with chocks.Step 6
Loosen the wheel bolts. Use wheel impact socket #17. Use a tap wrench. - Step 7Raise the car.Replacement: coil springs – MERCEDES-BENZ E-CLASS Coupe (C124). Tip:If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.Step 8
Unscrew the wheel bolts.AUTODOC recommends:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 9
Remove the wheel. - Step 10
Clean the lower shock absorber fastener. Use a wire brush. Use WD-40 spray. - Step 11Support the rear control arm. Use a hydraulic transmission jack.Step 12
Unscrew the lower fasteners of the shock absorber. Use a combination spanner #17. Use a drive socket #17. Use a ratchet wrench. - Step 13
Unscrew the upper fastener of the shock absorber. - Step 14
Remove the elements of the shock absorber upper mount. - Step 15
Remove the fastening bolt. - Step 16
Remove the shock absorber. - Step 17
Clean the shock absorber mounting seats. Use a wire brush. Use all-purpose cleaning spray. - Step 18
Clean the control arm fasteners. Use a wire brush. Use WD-40 spray. - Step 19
Clean the fastener connecting the sway bar link to the suspension arm. Use a wire brush. Use WD-40 spray. - Step 20
Unscrew the fastener connecting the stabilizer link to the control arm. Use a combination spanner #13. Use a drive socket #13. Use a ratchet wrench. - Step 21
Remove the fastening bolt. - Step 22Detach the sway bar link from the suspension arm.Step 23
Loosen the fastener that connects the control arm to the rear knuckle. Use a combination spanner #22. Use a drive socket #22. Use a ratchet wrench. - Step 24
Remove the support from under the rear control arm.AUTODOC recommends:Replacement: coil springs – MERCEDES-BENZ E-CLASS Coupe (C124). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms. - Step 25
Support the rear control arm where it is attached to the subframe. Use a hydraulic transmission jack. - Step 26
Unscrew the fastener connecting the control arm to the subframe. Use a combination spanner #19. Use a drive socket #19. Use a ratchet wrench. - Step 27
Remove the fastening bolt. Use a pin punch. Use a hammer. - Step 28
Detach the control arm from the subframe and lower the hydraulic transmission jack. If necessary, use a crowbar.AUTODOC recommends:As the control arm is spring loaded, the hydraulic transmission jack should be lowered strictly vertically to prevent the arm from slipping off abruptly and being displaced. - Step 29
Remove the spring. - Step 30
Clean the coil spring mounting seats. Use a wire brush. Use all-purpose cleaning spray. - Step 31
Clean the suspension arm mounting seats. Use a wire brush. Use all-purpose cleaning spray. - Step 32
Install the rubber spacer on the new coil spring. - Step 33
Install the spring.Replacement: coil springs – MERCEDES-BENZ E-CLASS Coupe (C124). AUTODOC recommends:Make sure that the coil spring is correctly positioned in its mounting seats. - Step 34
Install the control arm on the subframe. Use a hydraulic transmission jack. Use a crowbar.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the MERCEDES-BENZ E-Class Coupe (C124) model
Popular maintenance tutorials for Mercedes C124
Complete guides for changing the Springs on different MERCEDES-BENZ E-CLASS models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your MERCEDES-BENZ E-Class Coupe (C124)
View more
How to remove rust | AUTODOC tips
Easy Steps to Fix Minor Scratches on Your Vehicle | AUTODOC tips
5 most common causes of oil leaks | AUTODOC tips
2 ways to clean the EGR valve – which one is better?
Most commonly replaced car parts on MERCEDES-BENZ E-CLASS
Time to replace parts? Get even better deals in our Shop app.

SCAN ME
































