How to carry out replacement: Springs 1.6 (BK14) Mazda 3 BK
Disclaimer
Change Mazda 3 BK 2.3 MPS Springs yourself – manuals and video tutorials

How to change rear coil springs on MAZDA 3 Hatchback (BK) – replacement guide

downloads: 4
Views: 41
Download your free tutorial and fix MAZDA 3 (BK) 2.3 DiSi Turbo MPS (BK3P) problems yourself Download for free 1.64 MB Springs for Mazda 3 BK Shop now
Leave a comment Open in a new tab
Important!
This replacement procedure can be used for:
MAZDA 3 (BK) 1.3 (BK14), MAZDA 3 (BK) 1.6 DI Turbo, MAZDA 3 (BK) 2.0 (BKEP), MAZDA 3 (BK) 1.6 (BK14) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Springs for 3 (BK) and other MAZDA models
Alternative products
How to change Coil spring on Mazda 3 BK 1.6 (BK14) – step-by-step instructions for straightforward car repair Coil spring
Tools
Replacement: coil springs – MAZDA 3 (BK). Tools you might need:
Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #17
Drive socket # 17
HEX bit no.H6.
Wheel impact socket #19
Ratchet wrench
Torque wrench
Crow bar
Hydraulic transmission jack
Wheel chock
Buy tools
Replacement: coil springs – MAZDA 3 (BK). Tip from AUTODOC:
  • Both coil springs of the rear suspension should be replaced simultaneously.
  • The replacement procedure is identical for the left and right coil springs of the rear suspension.
  • Please note: all work on the car – MAZDA 3 (BK) – should be done with the engine switched off.
Carry out replacement in the following order:
  1. Step 1
    How to change Springs on Mazda 3 BK 2003 - free PDF and video manuals
    Secure the wheels with chocks.
  2. Step 2
    How to replace MAZDA 3 (BK) 1.6 (BK14) 2004 Springs - step-by-step manuals and video guides
    Loosen the wheel mounting bolts. Use wheel impact socket #19.
  3. Step 3
    Raise the rear of the car and secure on supports.
    Step 4
    Mazda 3 BK 1.6 DI Turbo 2005 Springs replacement: free workshop manuals
    Unscrew the wheel bolts.
    AUTODOC recommends:
    Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. MAZDA 3 (BK)
  4. Step 5
    Changing Springs on MAZDA 3 (BK) 2.3 MPS Turbo (BK14) 2006 by yourself
    Remove the wheel.
  5. Step 6
    Clean the control arm fasteners. Use a wire brush. Use WD-40 spray.
    Step 7
    How to remove MAZDA 3 1.3 (BK14) 2007 Springs - online easy-to-follow instructions
    Unscrew the fastener connecting the control arm to the rear knuckle. Use a drive socket #17. Use a ratchet wrench.
  6. Step 8
    How to replace Springs on MAZDA 3 (BK) 2008: download PDF manuals and video instructions
    Support the arm. Use a hydraulic transmission jack.
  7. Step 9
    Clean the shock absorber fasteners. Use a wire brush. Use WD-40 spray.
    Step 10
    How hard is it to do yourself: Springs replacement on Mazda 3 BK 1.6 MZ-CD 2009 - download illustrated guide
    Unscrew the lower fastener of the shock absorber. Use a drive socket #17. Use a ratchet wrench.
  8. Step 11
    Remove the fastening bolts (2 pieces).
    Step 12
    Detach the lower part of the shock absorber.
    Step 13
    Need to know how to renew Springs on MAZDA 3 2003? This free workshop manual will help you to do it yourself
    Unscrew the fastener connecting the stabilizer link to the control arm. Use a combination spanner #17. Use HEX No.H6. Use a ratchet wrench.
  9. Step 14
    Remove the fastening bolt.
    Step 15
    Changing of Springs on Mazda 3 BK 2004 won't be an issue if you follow this illustrated step-by-step guide
    Remove the support from under the arm.
    AUTODOC recommends:
    Replacement: shock absorbers – MAZDA 3 (BK). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
  10. Step 16
    Pull down the suspension control arm. Use a crowbar.
    Step 17
    MAZDA 3 2.3 MPS Springs replacement: online guides and video tutorials
    Remove the spring.
  11. Step 18
    Replacing Springs on Mazda 3 BK 2006 1.6 (BK14) by yourself
    Remove the rubber spring spacer.
  12. Step 19
    3 (BK) 1.3 (BK14) 2007 Springs DIY replacement workshop manual
    Install the rubber spacer on the new coil spring.
  13. Step 20
    How to change Springs on MAZDA 3 (BK) 2008 - tips and tricks
    Install the spring.
    Replacement: coil springs – MAZDA 3 (BK). Professionals recommend:
    Make sure that the coil spring is correctly positioned in its mounting seats.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?

Find out which tyre and wheel sizes are compatible with the MAZDA 3 Hatchback (BK) model

Mazda 3 BK tyre size

Popular maintenance tutorials for Mazda 3 BK

More manuals for Mazda 3 BK

Complete guides for changing the Springs on different MAZDA 3 models

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

DIY MAZDA 3 (BK) Springs replacement - online guide
Tips & tricks for your MAZDA 3 (BK)
View more
  • How to change Springs on MAZDA 3 (BK) 2.0 (BKEP) - replacement tricks
    5 mistakes when replacing consumables
    5K views
    Published on: 06/02/2025
  • Changing Coil springs Mazda 3 BK 1.6 (BK14) - Replacement Tips
    #DIY Wheel Rim Restoration: Revive Scratches and Chips Easily!
    7K views
    Published on: 18/07/2024
  • Maintenance Hacks - MAZDA 3 (BK) 1.6 DI Turbo Spring replacement guide
    Prevent Breakdowns: Key Car Checks After Winter | AUTODOC Guide
    3K views
    Published on: 23/03/2023
  • Replace Suspension spring on Mazda 3 BK - free video tips
    Top 5 reasons why your car squeals | AUTODOC Tips
    9K views
    Published on: 26/10/2023

Most commonly replaced car parts on MAZDA 3

Professional manuals for the most common MAZDA models

Autodoc CLUB App icon
Time to replace parts? Get even better deals in our Shop app.
MAZDA 3 (BK) Springs replace by yourself - Scan QR-code and download AUTODOC CLUB app
SCAN ME