How to change rear brake discs on BMW 1 Hatchback (E87) – replacement guide
BMW 1 Hatchback (E87) 118 i, BMW 1 Hatchback (E87) 118 i, BMW 1 Hatchback (E87) 118 i, BMW 1 Hatchback (E87) 120i, BMW 1 Hatchback (E87) 120i, BMW 1 Hatchback (E87) 120i, BMW 1 Hatchback (E87) 120i, BMW 1 Hatchback (E87) 118 i … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle

- Replace the brake disks on the car BMW 1 (E87) in complete set for each axis. Regardless of the state of components. This will ensure even braking.
- The replacement procedure is identical for both brake disks on the same axle.
- When changing the brake discs, always replace the brake pads.
- Please note: all work on the car – BMW 1 (E87) – should be done with the engine switched off.
- Step 1
Open the bonnet. Unscrew the brake fluid reservoir cap.
Step 2
Secure the wheels with chocks.
- Step 3

Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 4
Raise the rear of the car and secure on supports.
Step 5
Unscrew the wheel bolts.
AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. BMW 1 (E87)
- Step 6

Remove the wheel.
- Step 7
Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
Step 8
Unscrew the brake caliper fastening. Use a combination spanner #13. Use a combination spanner #15.
- Step 9
Spread the brake pads. Use a crowbar.
Step 10
Remove the brake caliper.
Replacement: brake discs – BMW 1 (E87). AUTODOC recommends:Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
- Step 11

Remove the brake pads. Use a flat screwdriver.
- Step 12
Remove the brake pads retaining clips. Use a flat screwdriver.
Step 13
Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
- Step 14

Unscrew the caliper bracket fastening. Use a drive socket #16. Use a ratchet wrench.
- Step 15
Remove the fastening bolts (2 pieces).
Step 16
Remove the caliper bracket.
- Step 17
Clean the brake disc fasteners. Use a wire brush. Use WD-40 spray.
Step 18
Unscrew the brake disc fastening. Use HEX No.H6. Use a ratchet wrench.
- Step 19

Remove the brake disc.
- Step 20

Clean the hub. Use a wire brush. Treat the contacting surface. Use copper grease.
- Step 21

Install the brake disc.
- Step 22

Tighten the brake disc fastening. Use HEX No.H6. Use a torque wrench. Tighten it to 16 Nm torque.
- Step 23

Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.
AUTODOC recommends:Replacement: brake discs – BMW 1 (E87). After applying the spray, wait a few minutes.
- Step 24

Remove the guide pins from the brake caliper.
Find out which tyre and wheel sizes are compatible with the BMW 1 Hatchback (E87) model
Popular maintenance tutorials for BMW E87
Complete guides for changing the Brake rotors on different BMW 1 SERIES models
Track expenses, manage logs, schedule replacements, and more.
Car lost power? Here's why your engine loses thrust
How to remove scratches from car plastic | AUTODOC tips
DIY rear axle restoration | Drivetrain restoration – Part 2
How to easily repair a punctured tyre | AUTODOC tips
Most commonly replaced car parts on BMW 1 SERIES





































