Disclaimer
How to change rear brake caliper on SEAT Toledo III (5P2) – replacement guide
downloads:
2
Views:
29
Recommended replacement interval for the part category Brake caliper : 100000 km
Important!
This replacement procedure can be used for:
SEAT Toledo III (5P2) 1.6, SEAT Toledo III (5P2) 2.0 FSI, SEAT Toledo III (5P2) 1.9 TDI, SEAT Toledo III (5P2) 2.0 TDI 16V, SEAT Toledo III (5P2) 1.8 TFSI, SEAT Toledo III (5P2) 2.0 TDI, SEAT Toledo III (5P2) 2.0 TFSI, SEAT Toledo III (5P2) 2.0 TDI, SEAT Toledo III (5P2) 2.0 TDI, SEAT Toledo III (5P2) 1.4 16V, SEAT Toledo III (5P2) 1.4 TSI … View more
The steps may slightly vary depending on the car design.
SEAT Toledo III (5P2) 1.6, SEAT Toledo III (5P2) 2.0 FSI, SEAT Toledo III (5P2) 1.9 TDI, SEAT Toledo III (5P2) 2.0 TDI 16V, SEAT Toledo III (5P2) 1.8 TFSI, SEAT Toledo III (5P2) 2.0 TDI, SEAT Toledo III (5P2) 2.0 TFSI, SEAT Toledo III (5P2) 2.0 TDI, SEAT Toledo III (5P2) 2.0 TDI, SEAT Toledo III (5P2) 1.4 16V, SEAT Toledo III (5P2) 1.4 TSI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Brake Calipers for Toledo III (5P2) and other SEAT models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #11
Combination spanner #13
Combination spanner #15
Drive socket # 11
Drive socket # 13
Wheel impact socket #17
Torque wrench
Crow bar
Rubber mallet
Fluid container
Brake hose clip
Water pump pliers
Brake bleeder kit
Wheel chock
Replacement: brake caliper – SEAT TOLEDO III (5P2). AUTODOC experts recommend:
- The replacement procedure is identical for the left and right brake calipers on the same axle.
- All work should be done with the engine stopped.
Replacement: brake caliper – SEAT TOLEDO III (5P2). Take the following steps:
- Step 1
Open the bonnet. Unscrew the brake fluid reservoir cap. - Step 2
Secure the wheels with chocks. - Step 3
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 4Raise the rear of the car and secure on supports.Step 5
Unscrew the wheel bolts.Replacement: brake caliper – SEAT TOLEDO III (5P2). AUTODOC recommends:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 6
Remove the wheel. - Step 7
Clean the parking brake bracket. Use a wire brush. Use WD-40 spray. - Step 8
Press the parking brake actuator lever on the brake caliper. - Step 9
Release the parking brake cable. Use water pump pliers. - Step 10
Clean the area where the brake hose is connected to the brake caliper and to the brake circuit pipe. Use a wire brush. Use WD-40 spray. - Step 11
Clamp the brake hose off using a brake hose clamp. - Step 12
Put a container for gathering brake fluid beneath. - Step 13
Unscrew the brake pipe from the brake hose. Use a combination spanner #11. - Step 14
Loosen the fastener connecting the brake pipe to the brake caliper. Use a combination spanner #11. - Step 15
Remove the brake hose retaining clip. Use a crowbar. - Step 16
Detach the brake pipe from the brake hose. - Step 17
Unscrew the brake caliper fastening. Use a combination spanner #13. Use a combination spanner #15. - Step 18
Remove the brake caliper.Replacement: brake caliper – SEAT TOLEDO III (5P2). Professionals recommend:When replacing the brake caliper, it is recommended to check the brake hose for damages and, if necessary, to replace it with a new one. When replacing a brake caliper it is recommended to replace brake pads, check the state of the brake discs and replace them with new ones if necessary.If no new guide pins were supplied in a kit with the new brake calipers, use the old pins. - Step 19
Unscrew the fastener connecting the brake pipe to the brake caliper. Use a combination spanner #11. - Step 20Detach the brake pipe from the brake caliper.Step 21
Treat the brake pipe. Use a brake cleaner.AUTODOC recommends:Replacement: brake caliper – SEAT TOLEDO III (5P2). After applying the spray, wait a few minutes. - Step 22
Reattach the brake pipe to the brake caliper. - Step 23
Screw in the fastener connecting the brake pipe to the brake caliper. Use a combination spanner #11. - Step 24
Install the brake caliper and fix it. Use a combination spanner #13. Use a combination spanner #15. - Step 25
Treat the brake hose. Treat the brake pipe. Use a brake cleaner.Replacement: brake caliper – SEAT TOLEDO III (5P2). Tip from AUTODOC experts:After applying the spray, wait a few minutes. - Step 26
Reattach the brake pipe to the brake hose.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the SEAT Toledo III (5P2) model
Popular maintenance tutorials for Seat Toledo 3
Complete guides for changing the Brake calipers on different SEAT TOLEDO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your SEAT Toledo III (5P2)
View more
How to Use Sandblasting Equipment: Step-by-Step Guide | AUTODOC Tips
Transform Your Engine Bay: Affordable Valve Cover Restoration with AUTODOC
Save Money on Fuel with These Easy Tips | AUTODOC
3 essential tips for choosing summer tyres | Get ready for warmer weather
Most commonly replaced car parts on SEAT TOLEDO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME




































