
Disclaimer
How to change front brake pads on SEAT Toledo III (5P2) – replacement guide
downloads:
0
Views:
8

Recommended replacement interval for the part category Brake pad set : 30000 km
Important!
This replacement procedure can be used for:
SEAT Toledo III (5P2) 2.0 FSI, SEAT Toledo III (5P2) 1.9 TDI, SEAT Toledo III (5P2) 2.0 TDI 16V, SEAT Toledo III (5P2) 1.8 TFSI, SEAT Toledo III (5P2) 2.0 TDI, SEAT Toledo III (5P2) 2.0 TFSI, SEAT Toledo III (5P2) 2.0 TDI, SEAT Toledo III (5P2) 2.0 TDI, SEAT Toledo III (5P2) 1.4 16V, SEAT Toledo III (5P2) 1.4 TSI … View more
The steps may slightly vary depending on the car design.
SEAT Toledo III (5P2) 2.0 FSI, SEAT Toledo III (5P2) 1.9 TDI, SEAT Toledo III (5P2) 2.0 TDI 16V, SEAT Toledo III (5P2) 1.8 TFSI, SEAT Toledo III (5P2) 2.0 TDI, SEAT Toledo III (5P2) 2.0 TFSI, SEAT Toledo III (5P2) 2.0 TDI, SEAT Toledo III (5P2) 2.0 TDI, SEAT Toledo III (5P2) 1.4 16V, SEAT Toledo III (5P2) 1.4 TSI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Brake Pads for Toledo III (5P2) and other SEAT models
Brake pad set
Alternative products

Wire brush
Nylon cleaning brush
Brake cleaner
Anti-squeal paste
Ceramic grease
Torque wrench
HEX bit No.H7
Wheel impact socket #17
Ratchet wrench
Brake caliper wind back tool
Crow bar
Wheel chock
Replacement: brake pads – SEAT TOLEDO III (5P2). AUTODOC experts recommend:
- Perform the replacement of brake pads in complete set for each axis. This provides effective braking.
- The replacement procedure is identical for all brake pads on the same axle.
- Please note: all work on the car – SEAT TOLEDO III (5P2) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Open the bonnet. Unscrew the brake fluid reservoir cap.Step 2Secure the wheels with chocks.Step 3Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 4Raise the car.AUTODOC recommends:If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.Step 5Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. SEAT TOLEDO III (5P2)
- Step 6Remove the wheel.
- Step 7Detach the brake caliper retaining spring. Use a crowbar.
- Step 8Spread the brake pads. Use a crowbar.
- Step 9Remove the dust boot caps of the brake caliper guide pins. Use a crowbar.
- Step 10Unscrew the brake caliper fasteners. Use HEX No.H7. Use a ratchet wrench.
- Step 11Remove the brake caliper.AUTODOC recommends:Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
- Step 12Remove the brake pads.Replacement: brake pads – SEAT TOLEDO III (5P2). Tip:Measure the brake disc thickness. Upon reaching the wear limit the part must be replaced.
- Step 13Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.AUTODOC recommends:Replacement: brake pads – SEAT TOLEDO III (5P2). After applying the spray, wait a few minutes.Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
- Step 14Remove the brake caliper guide pins.
- Step 15Clean the brake caliper guide pins. Use a brake cleaner.AUTODOC recommends:After applying the spray, wait a few minutes.
- Step 16Treat the brake caliper piston. Use a nylon cleaning brush. Use a brake cleaner.AUTODOC recommends:Replacement: brake pads – SEAT TOLEDO III (5P2). After applying the spray, wait a few minutes.
- Step 17Press in the brake caliper piston. Use brake caliper wind back tool.
- Step 18Install the brake caliper guide pins.
- Step 19Treat the brake pads in the area where their surface comes into contact with the brake caliper bracket. Use anti-squeal paste.Replacement: brake pads – SEAT TOLEDO III (5P2). AUTODOC experts recommend:Make sure the disc surface is clean before installing the pads.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the SEAT Toledo III (5P2) model
Popular maintenance tutorials for Seat Toledo 3
Complete guides for changing the Brake pad set on different SEAT TOLEDO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your SEAT Toledo III (5P2)
View more
- What to do if your check engine light is on | AUTODOC tips
- Don’t Replace, Just Polish! Headlight Restoration with AUTODOC
- Checking the starter without removing it | AUTODOC tips
- Understanding Airbag Light Warnings | Essential Tips for Car Safety
Most commonly replaced car parts on SEAT TOLEDO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME