Disclaimer
How to change lambda sensor on VW New Beetle Convertible (1Y7) – replacement guide
downloads:
1
Views:
67
Recommended replacement interval for the part category Lambda sensor : 100000 km
Important!
This replacement procedure can be used for:
VW New Beetle Convertible (1Y7) 1.6, VW New Beetle Convertible (1Y7) 2.0, VW New Beetle Convertible (1Y7) 1.4, VW New Beetle Convertible (1Y7) 1.8 T, VW New Beetle Convertible (1Y7) 2.5 … View more
The steps may slightly vary depending on the car design.
VW New Beetle Convertible (1Y7) 1.6, VW New Beetle Convertible (1Y7) 2.0, VW New Beetle Convertible (1Y7) 1.4, VW New Beetle Convertible (1Y7) 1.8 T, VW New Beetle Convertible (1Y7) 2.5 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Lambda Sensor for New Beetle Convertible (1Y7) and other VW models
Lambda sensor
Lambda sensor
Electronic spray
High-temperature ceramic grease
Torque wrench
Drive socket # 10
22-mm oxygen sensor socket
Ratchet wrench
Thread tap
Fender cover
Replacement: lambda sensor – VW NEW BEETLE Convertible (1Y7). AUTODOC experts recommend:
- After replacing the oxygen sensor, clear the trouble code from the electronic control unit and let the ECU adapt itself to the new sensor.
- Before getting down to work, start the engine and let it warm up to operating temperature.
- Please note: all work on the car – VW NEW BEETLE Convertible (1Y7) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Open the bonnet.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3Lift the car using a jack or place it over an inspection pit.Step 4
Unscrew the fasteners of the oxygen sensor housing cover. Use a drive socket #10. Use a ratchet wrench. - Step 5
Remove the oxygen sensor housing cover. - Step 6
Detach the oxygen sensor connector. - Step 7
Unscrew the oxygen sensor fastener. Use a 22-mm oxygen sensor socket. Use a ratchet wrench. - Step 8
Remove the oxygen sensor. - Step 9
Cut the thread for the new oxygen sensor. Use a thread tap. Use a ratchet wrench. - Step 10Treat the oxygen sensor. Use high-temperature ceramic grease.Step 11
Install the new oxygen sensor. - Step 12
Tighten the oxygen sensor fastener. Use a 22-mm oxygen sensor socket. Use a torque wrench. Tighten it to 37 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the VW New Beetle Convertible (1Y7) model.
Popular maintenance tutorials for VW New Beetle Convertible
Free download PDF
1.43 MB
Free download PDF1.2 MB
Free download PDF972.8 KB
Free download PDF1.84 MB
Free download PDF1003.52 KB
Free download PDF2.3 MB
Complete guides for changing the Oxygen sensor on different VW NEW BEETLE models
Free download PDF890.88 KB
Free download PDF1 MB
Free download PDF1.29 MB
Free download PDF1.36 MB
Free download PDF890.88 KB
Free download PDF890.88 KB
Your profile is your personal assistant.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- - scan the QR code
- - download from App Store
- - download from Google Play
Tips & tricks for your VW New Beetle Convertible (1Y7)
View more
How to polish your car | AUTODOC tips
What to do if your car heater isn't working | AUTODOC tips
How to polish an old engine valve cover to a shiny finish | AUTODOC Tips
TOP 6 WD-40 lifehacks | AUTODOC tips
