Disclaimer
How to change lambda sensor on Seat Leon 1M1 – replacement guide
downloads:
11
Views:
129
Recommended replacement interval for the part category Lambda sensor : 100000 km
Important!
This replacement procedure can be used for:
SEAT Leon Hatchback (1M1) 1.4 16V, SEAT Leon Hatchback (1M1) 1.8 20V T, SEAT Leon Hatchback (1M1) 1.6, SEAT Leon Hatchback (1M1) 1.6, SEAT Leon Hatchback (1M1) 1.8 20V … View more
The steps may slightly vary depending on the car design.
SEAT Leon Hatchback (1M1) 1.4 16V, SEAT Leon Hatchback (1M1) 1.8 20V T, SEAT Leon Hatchback (1M1) 1.6, SEAT Leon Hatchback (1M1) 1.6, SEAT Leon Hatchback (1M1) 1.8 20V … View more
The steps may slightly vary depending on the car design.
How to change lambda sensor on SEAT LEON 1M1 [TUTORIAL AUTODOC]
All the parts you need to replace – Lambda Sensor for Leon Hatchback (1M1) and other SEAT models
Lambda sensor
Alternative products
Lambda sensor
Wire brush
WD-40 spray
Electronic spray
High-temperature ceramic grease
Torque wrench
Drive socket # 10
22-mm oxygen sensor socket
Thread tap
Ratchet wrench
Replacement: lambda sensor – Seat Leon 1M1. AUTODOC experts recommend:
- After replacing the oxygen sensor, clear the trouble code from the electronic control unit and let the ECU adapt itself to the new sensor.
- Before getting down to work, start the engine and let it warm up to operating temperature.
- Please note: all work on the car – Seat Leon 1M1 – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1
Lift the car using a jack or place it over an inspection pit. - Step 2
Unscrew the fasteners of the oxygen sensor housing cover. Use a drive socket #10. Use a ratchet wrench. - Step 3
Remove the oxygen sensor housing cover. - Step 4
Detach the oxygen sensor connector. - Step 5
Disconnect the oxygen sensor wiring. - Step 6
Clean the oxygen sensor fastener. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the oxygen sensor fastener. Use a 22-mm oxygen sensor socket. Use a ratchet wrench. - Step 8
Remove the oxygen sensor. - Step 9
Clean the thread to prepare it for installing a new oxygen sensor. Use a thread tap. Use a ratchet wrench.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the SEAT Leon I Hatchback (1M1) model.
Popular maintenance tutorials for Seat Leon 1m1
Free download PDF
1013.76 KB
Free download PDF1.02 MB
Free download PDF901.12 KB
Free download PDF1.18 MB
Free download PDF972.8 KB
Free download PDF2.76 MB
Complete guides for changing the Oxygen sensor on different SEAT LEON models
Free download PDF1.05 MB
Free download PDF1 MB
Free download PDF890.88 KB
Free download PDF890.88 KB
Free download PDF890.88 KB
Free download PDF1.05 MB
Your profile is your personal assistant.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- - scan the QR code
- - download from App Store
- - download from Google Play
Tips & tricks for your SEAT Leon Hatchback (1M1)
View more
Top 5 Car Interior Cleaning Mistakes You Should Avoid | AUTODOC Tips
DIY alternator repair | AUTODOC tips
#DIY guide: Changing your car's color with a spray can | AUTODOC tips
DIY brake caliper restoration | AUTODOC tips
