How to carry out replacement: Wheel Bearing S4 2.2 Turbo quattro Audi 100 C4 Avant
Disclaimer
Change Audi 100 C4 Avant 2.3 E quattro Wheel Bearing yourself – manuals and video tutorials

How to change front wheel bearing on AUDI 100 C4 Avant (4A5) – replacement guide

downloads: 0
Views: 3
Download your free tutorial and fix AUDI 100 Avant (4A5, C4) 2.8 E problems yourself Download for free 3.95 MB Wheel Bearing for Audi 100 C4 Avant Shop now
Leave a comment Open in a new tab
Important!
This replacement procedure can be used for:
AUDI 100 Avant (4A5, C4) 2.5 TDI, AUDI 100 Avant (4A5, C4) 2.0 E, AUDI 100 Avant (4A5, C4) 2.0 E, AUDI 100 Avant (4A5, C4) S4 Turbo quattro, AUDI 100 Avant (4A5, C4) 2.6, AUDI 100 Avant (4A5, C4) 2.3 E, AUDI 100 Avant (4A5, C4) 2.8 E, AUDI 100 Avant (4A5, C4) 2.3 E quattro, AUDI 100 Avant (4A5, C4) 2.6 quattro, AUDI 100 Avant (4A5, C4) 2.8 E quattro, AUDI 100 Avant (4A5, C4) S4 V8 quattro, AUDI 100 Avant (4A5, C4) 2.0 E quattro, AUDI 100 Avant (4A5, C4) 2.4 D, AUDI 100 Avant (4A5, C4) 2.0 E 16V … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Wheel Bearing for 100 Avant (4A5, C4) and other AUDI models
Alternative products
How to change Wheel bearing kit on Audi 100 C4 Avant S4 2.2 Turbo quattro – step-by-step instructions for straightforward car repair Wheel bearing kit
Tools
Replacement: wheel bearing – AUDI 100 Avant (4A, C4). Tools you might need:
Wire brush
WD-40 spray
Electronic spray
Brake cleaner
Copper grease
Torque wrench
Combination spanner #13
Combination spanner #18
Drive socket # 10
Drive socket # 16
Drive socket # 17
Drive socket # 18
Drive socket # 27
HEX bit No.H8
Wheel impact socket #17
Ratchet wrench
Bush and bearing driver set
Ball joint puller
Flat screwdriver
Flat chisel
Tap wrench
Pin punch
Hammer
Crow bar
Hydraulic transmission jack
Wheel chock
Buy tools
AUTODOC recommends:
  • Do not re-use the bearing assembly of your AUDI 100 Avant (4A, C4) car.
  • The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
  • Please note: all work on the car – AUDI 100 Avant (4A, C4) – should be done with the engine switched off.
Carry out replacement in the following order:
  1. Step 1
    Open the bonnet. Unscrew the brake fluid reservoir cap.
    Step 2
    Secure the wheels with chocks.
    Step 3
    How to change Wheel Bearing on Audi 100 C4 Avant 1990 - free PDF and video manuals
    Loosen the wheel mounting bolts. Use wheel impact socket #17.
  2. Step 4
    Raise the front of the car and secure on supports.
    Step 5
    How to replace AUDI 100 Avant (4A5, C4) S4 2.2 Turbo quattro 1991 Wheel Bearing - step-by-step manuals and video guides
    Unscrew the wheel bolts.
    AUTODOC recommends:
    Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. AUDI 100 Avant (4A, C4)
  3. Step 6
    Audi 100 C4 Avant 2.3 E 1992 Wheel Bearing replacement: free workshop manuals
    Remove the wheel.
  4. Step 7
    Changing Wheel Bearing on AUDI 100 Avant (4A5, C4) 2.5 TDI 1993 by yourself
    Disconnect the ABS sensor wiring. Use a flat screwdriver.
  5. Step 8
    How to remove AUDI 100 2.6 quattro 1994 Wheel Bearing - online easy-to-follow instructions
    Detach the ABS sensor connector. Use a flat screwdriver.
  6. Step 9
    How to replace Wheel Bearing on AUDI 100 Avant (4A5, C4) 1990: download PDF manuals and video instructions
    Loosen the fastener of the driveshaft. Use a drive socket #27. Use a ratchet wrench.
  7. Step 10
    How hard is it to do yourself: Wheel Bearing replacement on Audi 100 C4 Avant S4 4.2 V8 quattro 1991 - download illustrated guide
    Spread the brake pads. Use a crowbar.
  8. Step 11
    Need to know how to renew Wheel Bearing on AUDI 100 1992? This free workshop manual will help you to do it yourself
    Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
  9. Step 12
    Changing of Wheel Bearing on Audi 100 C4 Avant 1993 won't be an issue if you follow this illustrated step-by-step guide
    Unscrew the caliper bracket fastening. Use a drive socket #17. Use a ratchet wrench. Use a tap wrench.
  10. Step 13
    AUDI 100 2.3 E quattro Wheel Bearing replacement: online guides and video tutorials
    Remove the caliper bracket.
  11. Step 14
    Replacing Wheel Bearing on Audi 100 C4 Avant 1990 S4 2.2 Turbo quattro by yourself
    Remove the fastening bolt. Use a drive socket #27.
  12. Step 15
    100 Avant (4A5, C4) 2.6 quattro 1991 Wheel Bearing DIY replacement workshop manual
    Remove the brake disc.
  13. Step 16
    How to change Wheel Bearing on AUDI 100 Avant (4A5, C4) 1992 - tips and tricks
    Clean all joints of the arm. Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.
  14. Step 17
    Step-by-step recommendations for DIY replacement Audi 100 C4 Avant 1993 2.6 quattro Wheel Bearing
    Unscrew the upper arm fastenings. Use a drive socket #16. Use HEX No.H8. Use a ratchet wrench.
  15. Step 18
    DIY replacement of Wheel Bearing on AUDI 100 Avant (4A5, C4) 2.6 1994 is not an issue anymore with our step-by-step tutorial
    Loosen the tie rod end fastening bolt. Use a drive socket #16. Use a ratchet wrench.
  16. Step 19
    How to change Wheel Bearing on Audi 100 C4 Avant 1990 - free PDF and video manuals
    Remove the fastening bolt. Use a pin punch. Use a hammer.
  17. Step 20
    How to replace AUDI 100 Avant (4A5, C4) S4 2.2 Turbo quattro 1991 Wheel Bearing - step-by-step manuals and video guides
    Loosen the tie rod end fastening bolt. Use a combination spanner #13.
  18. Step 21
    Audi 100 C4 Avant 2.3 E 1992 Wheel Bearing replacement: free workshop manuals
    Remove the fastening bolt.
  19. Step 22
    Changing Wheel Bearing on AUDI 100 Avant (4A5, C4) 2.5 TDI 1993 by yourself
    Spread the ears for the pinch bolt on the tie rod end. Use a flat metal-working chisel. Use a hammer.
  20. Step 23
    How to remove AUDI 100 2.6 quattro 1994 Wheel Bearing - online easy-to-follow instructions
    Disconnect the tie rod end from the steering knuckle.
  21. Step 24
    How to replace Wheel Bearing on AUDI 100 Avant (4A5, C4) 1990: download PDF manuals and video instructions
    Remove the fastening bolt.
  22. Step 25
    How hard is it to do yourself: Wheel Bearing replacement on Audi 100 C4 Avant S4 4.2 V8 quattro 1991 - download illustrated guide
    Clean the control arm fasteners. Use a wire brush. Use WD-40 spray.
  23. Step 26
    Need to know how to renew Wheel Bearing on AUDI 100 1992? This free workshop manual will help you to do it yourself
    Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #18.
  24. Step 27
    Changing of Wheel Bearing on Audi 100 C4 Avant 1993 won't be an issue if you follow this illustrated step-by-step guide
    Clean the control arm fasteners. Use a wire brush. Use WD-40 spray.
  25. Step 28
    AUDI 100 2.3 E quattro Wheel Bearing replacement: online guides and video tutorials
    Unscrew the lower arm fastener. Use a combination spanner #18. Use a drive socket #18. Use a ratchet wrench.
  26. Step 29
    Replacing Wheel Bearing on Audi 100 C4 Avant 1990 S4 2.2 Turbo quattro by yourself
    Prop up the steering knuckle. Use a hydraulic transmission jack.
  27. Step 30
    Treat all joints of the arm. Use WD-40 spray.
    Step 31
    100 Avant (4A5, C4) 2.6 quattro 1991 Wheel Bearing DIY replacement workshop manual
    Disconnect the ball joint from the steering knuckle. Use a ball joint puller. Use a crowbar.
  28. Step 32
    How to change Wheel Bearing on AUDI 100 Avant (4A5, C4) 1992 - tips and tricks
    Detach the driveshaft from the steering knuckle.
    Replacement: wheel bearing – AUDI 100 Avant (4A, C4). Tip from AUTODOC:
    Make sure that the drive shaft is not unloaded (when the car is jacked).
  29. Step 33
    Step-by-step recommendations for DIY replacement Audi 100 C4 Avant 1993 2.6 quattro Wheel Bearing
    Remove the support from under the steering knuckle.
    AUTODOC recommends:
    Replacement: wheel bearing – AUDI 100 Avant (4A, C4). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
  30. Step 34
    DIY replacement of Wheel Bearing on AUDI 100 Avant (4A5, C4) 2.6 1994 is not an issue anymore with our step-by-step tutorial
    Clean the control arm fasteners. Use a wire brush. Use WD-40 spray.
  31. Step 35
    How to change Wheel Bearing on Audi 100 C4 Avant 1990 - free PDF and video manuals
    Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #18.
  32. Step 36
    How to replace AUDI 100 Avant (4A5, C4) S4 2.2 Turbo quattro 1991 Wheel Bearing - step-by-step manuals and video guides
    Disconnect the ball joint from the steering knuckle. Use a ball joint puller. Use a crowbar.
  33. Step 37
    Audi 100 C4 Avant 2.3 E 1992 Wheel Bearing replacement: free workshop manuals
    Remove the steering knuckle together with the hub.
  34. Step 38
    Remove the control arms.
    Step 39
    Changing Wheel Bearing on AUDI 100 Avant (4A5, C4) 2.5 TDI 1993 by yourself
    Clean the fastener of the steering knuckle dust shield. Use a wire brush. Use WD-40 spray.
  35. Step 40
    How to remove AUDI 100 2.6 quattro 1994 Wheel Bearing - online easy-to-follow instructions
    Unscrew the fastener of the steering knuckle dust shield. Use a drive socket #10. Use a ratchet wrench.
  36. Step 41
    How to replace Wheel Bearing on AUDI 100 Avant (4A5, C4) 1990: download PDF manuals and video instructions
    Remove the wheel hub from the steering knuckle. Use a bush and bearing driver set.
  37. Step 42
    Clean the hub bearing mounting seat. Use a wire brush. Use WD-40 spray.
    Step 43
    How hard is it to do yourself: Wheel Bearing replacement on Audi 100 C4 Avant S4 4.2 V8 quattro 1991 - download illustrated guide
    Press out the wheel hub bearing. Use a bush and bearing driver set.
  38. Step 44
    Need to know how to renew Wheel Bearing on AUDI 100 1992? This free workshop manual will help you to do it yourself
    Clean the hub bearing mounting seat. Use a wire brush. Use WD-40 spray.
  39. Step 45
    Changing of Wheel Bearing on Audi 100 C4 Avant 1993 won't be an issue if you follow this illustrated step-by-step guide
    Press the new bearing in the steering knuckle. Use a bush and bearing driver set.
    Replacement: wheel bearing – AUDI 100 Avant (4A, C4). Tip:
    Check to make sure the wheel hub bearing is positioned correctly. Avoid its misalignment. Stop pressing on the surface of the bearing immediately after it has been fitted into its mounting seat.
  40. Step 46
    AUDI 100 2.3 E quattro Wheel Bearing replacement: online guides and video tutorials
    Clean the hub. Use WD-40 spray.
  41. Step 47
    Replacing Wheel Bearing on Audi 100 C4 Avant 1990 S4 2.2 Turbo quattro by yourself
    Install the wheel hub on the steering knuckle. Use a bush and bearing driver set.
  42. Step 48
    100 Avant (4A5, C4) 2.6 quattro 1991 Wheel Bearing DIY replacement workshop manual
    Tighten the fastener of the steering knuckle dust shield. Use a drive socket #10. Use a torque wrench. Tighten it to 4 Nm torque.
  43. Step 49
    How to change Wheel Bearing on AUDI 100 Avant (4A5, C4) 1992 - tips and tricks
    Treat the shock strut mounting seat on the steering knuckle. Use a wire brush. Use WD-40 spray.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?

Find out which tyre and wheel sizes are compatible with the AUDI 100 C4 Avant (4A5) model

Audi 100 C4 Avant tyre size

Popular maintenance tutorials for Audi 100 C4 Avant

More manuals for Audi 100 C4 Avant

Complete guides for changing the Wheel bearings on different AUDI 100 models

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

DIY AUDI 100 Avant (4A5, C4) Wheel Bearing replacement - online guide
Tips & tricks for your AUDI 100 Avant (4A5, C4)
View more
  • How to change Wheel bearings on AUDI 100 Avant (4A5, C4) 2.6 - replacement tricks
    Transform Your Car's Look: 6 Simple Accessories You Need to Try!
    3K views
    Published on: 18/11/2021
  • Changing Hub bearing Audi 100 C4 Avant S4 2.2 Turbo quattro - Replacement Tips
    DIY brake caliper restoration | AUTODOC tips
    746K views
    Published on: 02/06/2022
  • Maintenance Hacks - AUDI 100 Avant (4A5, C4) 2.3 E Wheel bearing kit replacement guide
    Reviving Your Car: How to Start After Extended Idle Time | AUTODOC Tips
    7K views
    Published on: 20/05/2021
  • Replace Wheel hub bearing on Audi 100 C4 Avant - free video tips
    Stop Rust Before It Starts: Top 5 Tips for Car Body Protection | AUTODOC Insights
    6K views
    Published on: 27/07/2023

Most commonly replaced car parts on AUDI 100

Professional manuals for the most common AUDI models

Autodoc CLUB App icon
Time to replace parts? Get even better deals in our Shop app.
AUDI 100 Avant (4A5, C4) Wheel Bearing replace by yourself - Scan QR-code and download AUTODOC CLUB app
SCAN ME