How to carry out replacement: Control Arm 2.0 CDTI (68) Vauxhall Insignia Mk1
Disclaimer
Change Vauxhall Insignia Mk1 2.0 CDTI (68) Control Arm yourself – manuals and video tutorials

How to change front lower arm on VAUXHALL Insignia Mk I (A) Hatchback (G09) – replacement guide

downloads: 40
Views: 422
Download your free tutorial and fix VAUXHALL Insignia Mk I (A) Hatchback (G09) 1.4 (68) problems yourself Download for free 1.68 MB Control Arm for Vauxhall Insignia Mk1 Shop now
Leave a comment Open in a new tab
Important!
This replacement procedure can be used for:
VAUXHALL Insignia Mk I (A) Hatchback (G09) 2.0 CDTI (68) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Control Arm for Insignia Mk I (A) Hatchback (G09) and other VAUXHALL models
Alternative products
How to change Suspension arm on Vauxhall Insignia Mk1 2.0 CDTI (68) – step-by-step instructions for straightforward car repair Suspension arm
Tools
Replacement: front lower arm – VAUXHALL INSIGNIA Mk I (A). List of the tools you'll need:
Wire brush
WD-40 spray
Copper grease
Drive socket # 18
Combination spanner #18
Wheel impact socket #17
Ratchet wrench
Torque wrench
Pin punch
Flat chisel
Hammer
Rubber mallet
Crow bar
Hydraulic transmission jack
Wheel chock
Buy tools
Replacement: front lower arm – VAUXHALL INSIGNIA Mk I (A). AUTODOC experts recommend:
  • The replacement procedure is identical for the left and right lower control arms.
  • All work should be done with the engine stopped.
Replacement: front lower arm – VAUXHALL INSIGNIA Mk I (A). Take the following steps:
  1. Step 1
    How to change Control Arm on Vauxhall Insignia Mk1 2008 - free PDF and video manuals
    Secure the wheels with chocks.
  2. Step 2
    How to replace VAUXHALL Insignia Mk I (A) Hatchback (G09) 2.0 CDTI (68) 2009 Control Arm - step-by-step manuals and video guides
    Loosen the wheel mounting bolts. Use wheel impact socket #17.
  3. Step 3
    Raise the front of the car and secure on supports.
    Step 4
    Vauxhall Insignia Mk1 1.8 (68) 2010 Control Arm replacement: free workshop manuals
    Unscrew the wheel bolts.
    AUTODOC recommends:
    Important! Hold the wheel while unscrewing the fastening bolts. VAUXHALL INSIGNIA Mk I (A)
  4. Step 5
    Changing Control Arm on VAUXHALL Insignia Mk I (A) Hatchback (G09) 1.4 (68) 2011 by yourself
    Remove the wheel.
  5. Step 6
    How to remove VAUXHALL INSIGNIA 2.0 CDTI (68) 2012 Control Arm - online easy-to-follow instructions
    Clean all joints of the arm. Use a wire brush. Treat all joints of the arm. Use WD-40 spray.
    Replacement: front lower arm – VAUXHALL INSIGNIA Mk I (A). Tip:
    After applying the spray, wait a few minutes.Wear protective goggles.
  6. Step 7
    How to replace Control Arm on VAUXHALL Insignia Mk I (A) Hatchback (G09) 2013: download PDF manuals and video instructions
    Unscrew the ball joint fastening to the steering knuckle. Use a drive socket #18. Use a ratchet wrench.
  7. Step 8
    How hard is it to do yourself: Control Arm replacement on Vauxhall Insignia Mk1 1.6 CDTI (68) 2014 - download illustrated guide
    Remove the fastening bolt. Use a hammer. Use a pin punch.
  8. Step 9
    Need to know how to renew Control Arm on VAUXHALL INSIGNIA 2015? This free workshop manual will help you to do it yourself
    Unscrew the front arm fastener. Use a drive socket #18. Use a combination spanner #18. Use a ratchet wrench.
  9. Step 10
    Changing of Control Arm on Vauxhall Insignia Mk1 2016 won't be an issue if you follow this illustrated step-by-step guide
    Unscrew the rear arm fastener. Use a drive socket #18. Use a combination spanner #18. Use a ratchet wrench.
  10. Step 11
    VAUXHALL INSIGNIA 2.0 CDTI (68) Control Arm replacement: online guides and video tutorials
    Release the fastener connecting the ball joint to the steering knuckle. Use a flat metal-working chisel. Use a hammer. Disconnect the ball joint from the steering knuckle.
  11. Step 12
    Replacing Control Arm on Vauxhall Insignia Mk1 2008 2.0 CDTI (68) by yourself
    Remove the arm. Use a crowbar.
  12. Step 13
    Insignia Mk I (A) Hatchback (G09) 2.0 CDTI (68) 2009 Control Arm DIY replacement workshop manual
    Clean the mounting seats and the thread of the suspension arm. Use a wire brush. Use WD-40 spray.
  13. Step 14
    How to change Control Arm on VAUXHALL Insignia Mk I (A) Hatchback (G09) 2010 - tips and tricks
    Install a new arm.
  14. Step 15
    Step-by-step recommendations for DIY replacement Vauxhall Insignia Mk1 2011 2.0 CDTI (68) Control Arm
    Connect the ball joint to the steering knuckle.
    Replacement: front lower arm – VAUXHALL INSIGNIA Mk I (A). AUTODOC recommends:
    During the installation process, use only new bolts and nuts.Do not damage the ball joint cover.
  15. Step 16
    DIY replacement of Control Arm on VAUXHALL Insignia Mk I (A) Hatchback (G09) 1.6 CDTI (68) 2012 is not an issue anymore with our step-by-step tutorial
    Install the control arm fasteners. Do not tighten it.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?

Find out which tyre and wheel sizes are compatible with the VAUXHALL Insignia Mk1 (A) Hatchback (G09) model

Vauxhall Insignia Mk1 tyre size

Popular maintenance tutorials for Vauxhall Insignia Mk1

More manuals for Vauxhall Insignia Mk1

Complete guides for changing the Control arm on different VAUXHALL INSIGNIA models

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

DIY VAUXHALL Insignia Mk I (A) Hatchback (G09) Control Arm replacement - online guide
Tips & tricks for your VAUXHALL Insignia Mk I (A) Hatchback (G09)
View more
  • How to change Control arm on VAUXHALL Insignia Mk I (A) Hatchback (G09) 1.6 CDTI (68) - replacement tricks
    How to choose the right engine oil for your car | AUTODOC
    12K views
    Published on: 01/07/2020
  • Changing Wishbone Vauxhall Insignia Mk1 2.0 CDTI (68) - Replacement Tips
    Initial Car Inspection: What to Check Before You Buy
    5K views
    Published on: 24/10/2020
  • Maintenance Hacks - VAUXHALL Insignia Mk I (A) Hatchback (G09) 1.8 (68) Control arms replacement guide
    Top 7 signs of a bad starter
    4K views
    Published on: 20/03/2025
  • Replace Trailing arm on Vauxhall Insignia Mk1 - free video tips
    Transform Your Car's Look: 6 Simple Accessories You Need to Try!
    3K views
    Published on: 18/11/2021

Most commonly replaced car parts on VAUXHALL INSIGNIA

Professional manuals for the most common VAUXHALL models

Autodoc CLUB App icon
Time to replace parts? Get even better deals in our Shop app.
VAUXHALL Insignia Mk I (A) Hatchback (G09) Control Arm replace by yourself - Scan QR-code and download AUTODOC CLUB app
SCAN ME