
Disclaimer
How to change front door lock on SEAT Toledo II Saloon (1M2) – replacement guide
downloads:
6
Views:
96
Important!
This replacement procedure can be used for:
SEAT Toledo II Saloon (1M2) 1.6, SEAT Toledo II Saloon (1M2) 1.8 20V, SEAT Toledo II Saloon (1M2) 2.3 V5, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.4 16V, SEAT Toledo II Saloon (1M2) 1.6 16V, SEAT Toledo II Saloon (1M2) 2.3 V5 20V, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.8 20VT … View more
The steps may slightly vary depending on the car design.
SEAT Toledo II Saloon (1M2) 1.6, SEAT Toledo II Saloon (1M2) 1.8 20V, SEAT Toledo II Saloon (1M2) 2.3 V5, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.4 16V, SEAT Toledo II Saloon (1M2) 1.6 16V, SEAT Toledo II Saloon (1M2) 2.3 V5 20V, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.8 20VT … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Door Lock for Toledo II Saloon (1M2) and other SEAT models
Door lock
Alternative products

Electronic spray
Torque wrench
Torx bit T20
Drive socket # 10
XZN socket bit # 8
Ratchet wrench
Painter's tape
Phillips screwdriver
Clip removal tool
Plastic trim tool
Replacement: door lock – SEAT TOLEDO II (1M2). Professionals recommend:
- The procedure for replacing the locks on the right and left front doors is identical.
- Please note: all work on the car – SEAT TOLEDO II (1M2) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Open the car door.
- Step 2Detach the door handle trim panel. Use a plastic trim tool.Replacement: door lock – SEAT TOLEDO II (1M2). AUTODOC recommends:Do not apply excessive force when removing the part. Otherwise you may damage it.
- Step 3Unscrew the door card fasteners. Use a Phillips screwdriver.
- Step 4Detach the door card. Use a plastic trim tool.AUTODOC recommends:Replacement: door lock – SEAT TOLEDO II (1M2). Do not use excessive force when removing the part as this may damage it.
- Step 5Detach the door lock actuator cable.
- Step 6Detach the bulb connector.
- Step 7Detach the speaker connector.
- Step 8Remove the covers from the window raiser fasteners. Use a plastic trim tool.
- Step 9Switch on the ignition.Step 10Lower the window glass.AUTODOC recommends:Continue lowering the window glass until its fasteners become visible.
- Step 11Switch off the ignition.Step 12Detach the connector for the power window switch module.
- Step 13Unscrew the window glass fasteners. Use a drive socket #10. Use a ratchet wrench.Replacement: door lock – SEAT TOLEDO II (1M2). Tip:To avoid injury, hold the glass when unscrewing the fasteners.
- Step 14Raise the window glass all the way up and secure it on the door frame with masking tape.AUTODOC recommends:To avoid injury, hold the glass when raising it.
- Step 15Detach the power mirror switch connector.
- Step 16Detach the speaker connector.
- Step 17Detach the power window connector.
- Step 18Detach the power window wiring harness. Use a clip removal tool.
- Step 19Remove the door panel covers. Use a plastic trim tool.
- Step 20Unscrew the door panel fasteners. Use a drive socket #10. Use a ratchet wrench.
- Step 21Unscrew the fastener of the exterior door handle. Use Torx T20. Use a ratchet wrench.
- Step 22Remove the cover from the exterior door handle fastener. Use a plastic trim tool.Replacement: door lock – SEAT TOLEDO II (1M2). Tip from AUTODOC experts:Do not apply excessive force when removing the part. Otherwise you may damage it.
- Step 23Unscrew the door lock fasteners. Use XZN #8. Use a ratchet wrench.
- Step 24Remove the door panel together with the window regulator linkage.AUTODOC recommends:Replacement: door lock – SEAT TOLEDO II (1M2). To avoid damaging the part when removing it, do not use excessive force.
- Step 25Detach the door lock connector.
- Step 26Remove the handle-to-lock cable. Use a plastic trim tool.
- Step 27Remove the door lock.AUTODOC recommends:Do not apply excessive force when removing the part. Otherwise you may damage it.
- Step 28Remove the handle-to-lock cable.
- Step 29Install the handle-to-lock cable.
- Step 30Remove the door lock rod.
- Step 31Install the door lock rod on the new lock.
- Step 32Remove the handle-to-lock cable.
- Step 33Install the handle-to-lock cable.
- Step 34Install the new lock.Replacement: door lock – SEAT TOLEDO II (1M2). AUTODOC experts recommend:When installing, do not use excessive force to avoid damage to the part.
- Step 35Install the handle-to-lock cable. Use a plastic trim tool.
- Step 36Install the cover on the exterior door handle fastener.
- Step 37Screw in the exterior door handle fastener. Use Torx T20. Use a ratchet wrench.
- Step 38Install the door panel together with the window regulator linkage.
- Step 39Treat the door lock connector. Use dielectric grease.
- Step 40Attach the door lock connector.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the SEAT Toledo II Saloon (1M2) model
Popular maintenance tutorials for Seat Toledo 1m
Complete guides for changing the Door lock mechanism on different SEAT TOLEDO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your SEAT Toledo II Saloon (1M2)
View more
- 5 more brake repair mistakes | Stop making these brake repair mistakes
- K2 ROTON wheel cleaner overview
- Transform Your Old Engine Valve Cover: Quick Polishing Tips for a Shiny Finish | AUTODOC Tips
- Stop Rust Before It Starts: Top 5 Tips for Car Body Protection | AUTODOC Insights
Most commonly replaced car parts on SEAT TOLEDO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME