Disclaimer

How to change front coil springs on SKODA Fabia II Combi (545) – replacement guide

downloads: 5

Important!

This replacement procedure can be used for:
SKODA Fabia II Combi (545) 1.2 TSI, SKODA Fabia II Combi (545) 1.2 TSI, SKODA Fabia II Combi (545) 1.6 … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Springs for Fabia II Combi (545) and other SKODA models

Alternative products

Coil spring

188C0293 RIDEX Coil spring

18,70 GBP

Shop

SKCS-0040292 STARK Coil spring

20,12 GBP

Shop

4095065 LESJÖFORS Coil spring

21,22 GBP

Shop

RH2958 KYB Coil spring

22,39 GBP

Shop

4085721 LESJÖFORS Coil spring

25,07 GBP

Shop

37822 FEBI BILSTEIN Coil spring

26,55 GBP

Shop

JCS214 TRW Coil spring

27,44 GBP

Shop

37-160678 BILSTEIN Coil spring

27,83 GBP

Shop

SP3386 MONROE Coil spring

29,63 GBP

Shop

56632 SPIDAN Coil spring

30,80 GBP

Shop

Replacement: coil springs – SKODA FABIA Combi. Tools you need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Drive socket # 12 
                    
                      Drive socket # 13 
                    
                      Drive socket # 16 
                    
                      Drive socket # 18 
                    
                      Drive socket # 21 
                    
                      XZN socket bit # 12 
                    
                      12-point socket # 30
                    
                      HEX bit no.H6
                    
                      Shock absorber socket
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Pin punch
                    
                      Tap wrench
                    
                      Hammer
                    
                      Hydraulic strut spring compressor
                    
                      Hydraulic transmission jack
                    
                      Fender cover
                    
                      Wheel chock

Buy tools

Replacement: coil springs – SKODA FABIA Combi. Tip from AUTODOC experts:

Both coil springs of the front suspension should be replaced simultaneously.
The replacement procedure is identical for the left and right coil springs of the front suspension.
All work should be done with the engine stopped.

Replacement: coil springs – SKODA FABIA Combi. Use the following procedure:

Step 1

Open the bonnet.

Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 3

Clean the fasteners of the shock strut upper mount. Use WD-40 spray.
Step 4

Loosen the upper fastener of the shock strut mount. Use a drive socket #13. Use a ratchet wrench.
Step 5

Secure the wheels with chocks.
Step 6

Unscrew the hub lock nut. Use 12-point socket No.30. Use a tap wrench.
Step 7

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 8

Raise the front of the car and secure on supports.

Step 9

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. SKODA FABIA Combi
Step 10

Remove the wheel.
Step 11

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 12

Unscrew the nut and remove the stabilizer rod from the shock strut. Use a drive socket #16. Use a ratchet wrench.
Step 13

Clean the fasteners connecting the shock strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 14

Detach the brake hose from the shock strut. Use a drive socket #12.
Step 15

Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use XZN #12. Use a drive socket #18. Use a ratchet wrench. Use a tap wrench.
Step 16

Clean all joints of the arm. Use a wire brush. Use WD-40 spray.

AUTODOC recommends:
Replacement: coil springs – SKODA FABIA Combi. After applying the spray, wait a few minutes.Wear protective goggles.
Step 17

Unscrew the fastener connecting the ball joint to the suspension control arm. Use a drive socket #13. Use a tap wrench.
Step 18

Disconnect the spherical joint from the arm.
Step 19

Unscrew the fastener connecting the drive shaft to the wheel hub. Use 12-point socket No.30.

Step 20

Remove the drive shaft. Use a pin punch. Use a hammer.

Step 21

Prop up the steering knuckle. Use a hydraulic transmission jack.
Step 22

Remove the fastening bolt.
Step 23

Release the lower fastener connecting the shock strut to the steering knuckle. Use a special drive socket to remove the shock absorber. Use a ratchet wrench.
Step 24

Disconnect the steering knuckle from the shock absorber strut.
Step 25

Unscrew the upper fastening of the shock absorber strut.

AUTODOC recommends:
SKODA FABIA Combi – To avoid injury, hold the suspension strut while unscrewing the fastening bolts.
Step 26

Remove the suspension strut.
Step 27

Set the shock absorber strut on the spring compressor tool.

Replacement: coil springs – SKODA FABIA Combi. Tip from AUTODOC experts:
Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
Step 28

Compress the spring.
Step 29

Treat the shock strut rod. Use a wire brush. Use WD-40 spray.
Step 30

Remove the strut piston rod nut. Use a drive socket #21. Use HEX No.H6. Use a ratchet wrench.
Step 31

Remove the shock absorber mount, boot and bump stop.
Step 32

Release the coil spring.
Step 33

Remove the spring.

AUTODOC recommends:
Replacement: coil springs – SKODA FABIA Combi. Carefully inspect the mount, the boot, and the bump stop of the shock absorber. Replace if necessary.
Step 34

Install the boot and a bump stop onto the shock absorber.
Step 35

Install the spring on the shock absorber.
Step 36

Compress the spring.
Step 37

Install the upper strut mount and the strut mount bearing.
Step 38

Tighten the shock strut piston rod nut. Use a drive socket #21. Use HEX No.H6. Use a torque wrench. Tighten it to 60 Nm torque.

AUTODOC recommends:
Replacement: coil springs – SKODA FABIA Combi. Be sure to position the filtering element correctly. Avoid misalignment.
Step 39

Decompress the spring.
Step 40

Remove the assembled shock strut.
Step 41

Install the shock strut into the wheel arch.
Step 42

Secure the upper fasteners of the shock strut. Do not tighten it.

AUTODOC recommends:
SKODA FABIA Combi – To avoid injury, hold the suspension strut while screwing in the fastening bolts.
Step 43

Treat the shock strut mounting seat on the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 44

Fix the shock absorber strut on the steering knuckle.
Step 45

Install the fastening bolt. Use a drive socket #18.
Step 46

Screw in the fastener that connects the shock strut to the steering knuckle. Use a drive socket #18. Use XZN #12. Use a ratchet wrench.
Step 47

Clean the splines of the drive shaft CV joint. Use a wire brush. Use WD-40 spray.
Step 48

Remove the support from under the steering knuckle.

AUTODOC recommends:
Replacement: coil springs – SKODA FABIA Combi. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 49

Mount the drive shaft into the wheel hub.
Step 50

Clean the ball joint mounting seat. Use a wire brush. Use WD-40 spray.
Step 51

Attach the ball joint to the control arm.
Step 52

Screw the fasteners of the ball joint. Use a drive socket #13.
Step 53

Tighten the lower fasteners connecting the shock strut to the steering knuckle. Use a drive socket #18. Use a torque wrench. Tighten it to 60 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 54

Tighten the ball joint fastener. Use a drive socket #13. Use a torque wrench. Tighten it to 20 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 55

Screw the nut of the drive shaft. Use 12-point socket No.30.
Step 56

Fasten the brake hose on the strut. Use a drive socket #12.
Step 57

Ιnstall the transverse stabilizer link.
Step 58

Tighten the fastener connecting the stabilizer link to the shock strut. Use a drive socket #16. Use a torque wrench. Tighten it to 40 Nm torque.
Step 59

Treat all joints of the arm. Treat the shock strut fasteners. Use copper grease.
Step 60

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 61

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: coil springs – SKODA FABIA Combi. After applying the spray, wait a few minutes.
Step 62

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. SKODA FABIA Combi
Step 63

Screw in the wheel bolts. Use wheel impact socket #17.
Step 64

Lower the car.

Step 65

Tighten the upper fastener of the shock absorber strut mount. Use a drive socket #13. Use a torque wrench. Tighten it to 15 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 66

Treat the fasteners of the shock strut mount. Use copper grease.
Step 67

Screw the wheel hub lock nut. Use 12-point socket No.30. Use a torque wrench. Tighten it to 50 Nm torque.+45°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 68

Tighten the wheel bolts using a criss-cross pattern. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120 Nm torque.

Step 69

Remove the jacks and chocks.

Step 70

Remove the fender protection cover.

Step 71

Close the hood.