Important!

This replacement procedure can be used for:
OPEL Meriva B (S10) 1.3 CDTI (75), OPEL Meriva B (S10) 1.3 CDTI (75), OPEL Meriva B (S10) 1.4 (75), OPEL Meriva B (S10) 1.4 (75), OPEL Meriva B (S10) 1.4 (75), OPEL Meriva B (S10) 1.4 LPG (75) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Springs for Meriva B (S10) and other OPEL models

Coil spring

        Coil spring for Meriva B (S10) Petrol/Petroleum Gas (LPG) (120 hp)
      
        Coil spring for Meriva B (S10) Petrol (100 hp)
      
        Coil spring for Meriva B (S10) Petrol (120 hp)
      
        Coil spring for Meriva B (S10) Petrol (140 hp)
      
        Coil spring for Meriva B (S10) Diesel (75 hp)
      
        Coil spring for Meriva B (S10) Diesel (95 hp)

Replacement: coil springs – OPEL MERIVA B. List of the tools you'll need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Brake cleaner 
                      
                        Copper grease 
                      
                        Combination spanner #18
                      
                        Combination spanner #19
                      
                        HEX bit no.H6.
                      
                        Drive socket # 18 
                      
                        Drive socket # 19 
                      
                        Drive socket # 22 
                      
                        Wheel impact socket #17
                      
                        Ratchet wrench
                      
                        Torque wrench
                      
                        Flat Screwdriver
                      
                        Tap wrench
                      
                        Clip removal tool
                      
                        Water pump pliers
                      
                        Crow bar
                      
                        Rubber mallet
                      
                        Hydraulic strut spring compressor
                      
                        Hydraulic transmission jack
                      
                        Fender cover
                      
                        Wheel chock

Buy tools

Replacement: coil springs – OPEL MERIVA B. AUTODOC experts recommend:

Both coil springs of the front suspension should be replaced simultaneously.
The replacement procedure is identical for the left and right coil springs of the front suspension.
Please note: all work on the car – OPEL MERIVA B – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Open the hood.

Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 3

Remove the cowl grille seal.
Step 4

Raise up and remove the cowl grille.
Step 5

Remove the shock strut mount cap. Use a flat screwdriver.
Step 6

Clean the fasteners of the shock strut upper mount. Use a wire brush. Use WD-40 spray.
Step 7

Remove the retainer of the shock strut upper mount. Use a clip removal tool.
Step 8

Secure the wheels with chocks.
Step 9

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 10

Raise the front of the car and secure on supports.

Step 11

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. OPEL MERIVA B
Step 12

Remove the wheel.
Step 13

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 14

Unscrew the nut and remove the stabilizer rod from the shock strut. Use a combination spanner #19. Use a drive socket #19. Use a ratchet wrench.
Step 15

Remove the stabilizer rod.

Step 16

Clean the fasteners connecting the shock strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 17

Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a tap wrench.
Step 18

Clean the fasteners of the ABS sensor and of the brake hose which connect them to the shock strut. Use a wire brush. Use WD-40 spray.
Step 19

Disconnect the fastener of the ABS sensor cable from the shock absorber strut. Use a flat screwdriver.
Step 20

Detach the brake hose from the shock strut. Use water pump pliers.
Step 21

Prop up the steering knuckle. Use a hydraulic transmission jack.

Step 22

Remove the fastening bolts.
Step 23

Disconnect the steering knuckle from the shock absorber strut. Use a crowbar.
Step 24

Remove the retainer of the shock strut upper mount.

Replacement: coil springs – OPEL MERIVA B. AUTODOC recommends:
To avoid injury, hold the shock strut firmly when dismantling it.
Step 25

Remove the suspension strut.
Step 26

Set the shock absorber strut on the spring compressor tool.

Replacement: coil springs – OPEL MERIVA B. Tip from AUTODOC experts:
Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
Step 27

Compress the spring.
Step 28

Remove the strut piston rod nut. Use HEX No.H6. Use a drive socket #22. Use a ratchet wrench.
Step 29

Remove the top strut mount.
Step 30

Release the coil spring.
Step 31

Remove the shock absorber dust cap and the bump stop.

AUTODOC recommends:
Replacement: coil springs – OPEL MERIVA B. Carefully inspect the mount, the boot, and the bump stop of the shock absorber. Replace if necessary.
Step 32

Remove the spring.
Step 33

Install the spring on the shock absorber.
Step 34

Compress the spring.
Step 35

Install the mount, the boot and the bump stop on the shock absorber.
Step 36

Tighten the shock strut piston rod nut. Use HEX No.H6. Use a drive socket #22. Use a torque wrench. Tighten it to 65 Nm torque.

Replacement: coil springs – OPEL MERIVA B. Tip:
Check to make sure the spring is positioned correctly. Avoid its misalignment.
Step 37

Decompress the spring.
Step 38

Remove the assembled shock strut.
Step 39

Treat the shock strut rod. Use copper grease.

Step 40

Install the shock strut into the wheel arch.

AUTODOC recommends:
To avoid injury, hold the shock strut firmly when mounting it.
Step 41

Treat the shock strut mounting seat on the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 42

Fix the shock absorber strut on the steering knuckle.
Step 43

Install the fastening bolts.
Step 44

Raise the hydraulic transmission jack by 10-15 cm.
Step 45

Install the retainer of the shock strut upper mount. Use water pump pliers.
Step 46

Connect the fastener of the ABS sensor cable to the shock absorber strut.
Step 47

Fasten the brake hose on the strut. Use a rubber mallet.
Step 48

Tighten the lower fasteners connecting the shock strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a torque wrench. Tighten it to 105 Nm torque.
Step 49

Ιnstall the transverse stabilizer link.
Step 50

Tighten the fastener connecting the stabilizer link to the shock strut. Use a drive socket #19. Use a combination spanner #19. Use a torque wrench. Tighten it to 55 Nm torque.
Step 51

Remove the support from under the steering knuckle.

AUTODOC recommends:
Replacement: coil springs – OPEL MERIVA B. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 52

Treat the shock strut fasteners. Treat all joints of the arm. Use copper grease.
Step 53

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 54

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: coil springs – OPEL MERIVA B. After applying the spray, wait a few minutes.
Step 55

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. OPEL MERIVA B
Step 56

Screw in the wheel bolts. Use wheel impact socket #17.
Step 57

Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 110 Nm torque.
Step 58

Install and secure the cowl grille.
Step 59

Install the shock strut mount cap.

Step 60

Install the cowl grille seal.
Step 61

Remove the jacks and chocks.

Step 62

Remove the fender protection cover.

Step 63

Close the hood.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the OPEL Meriva B (S10) model.

Browse tyres

How to change front brake pads on OPEL Meriva B (S10) – replacement guide

Free download PDF
1.45 MB
How to change rear brake pads on OPEL Meriva B (S10) – replacement guide

Free download PDF
2.34 MB
How to change rear brake discs on OPEL Meriva B (S10) – replacement guide

Free download PDF
2.4 MB
How to change front brake discs on OPEL Meriva B (S10) – replacement guide

Free download PDF
1.86 MB
How to change rear wheel bearing on OPEL Meriva B (S10) – replacement guide

Free download PDF
2.99 MB
How to change spark plugs on OPEL Meriva B (S10) – replacement guide

Free download PDF
1.25 MB

How to change front coil springs on Opel Meriva X03 – replacement guide

Free download PDF
3.89 MB
How to change rear coil springs on Opel Meriva X03 – replacement guide

Free download PDF
1.47 MB
How to change coil springs on a car – replacement tutorial

Universal

Free download PDF
1.91 MB
How to change front coil springs on Opel Corsa D – replacement guide

Free download PDF
3.86 MB
How to change front coil springs on Opel Zafira F75 – replacement guide

Free download PDF
3.76 MB
How to change front coil springs on Opel Zafira B A05 – replacement guide

Free download PDF
3.02 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

Top 5 reasons why your car squeals | AUTODOC Tips

6K views

Published on: 26/10/2023
Top 5 brake repair mistakes | AUTODOC tips

184K views

Published on: 27/10/2022
What to check when buying a used car | AUTODOC tips

5K views

Published on: 24/10/2020
How to wash your car in winter | AUTODOC tips

3K views

Published on: 31/01/2024