Disclaimer
How to change front brake pads on MERCEDES-BENZ E-Class Platform / Chassis (VF211) – replacement guide
downloads:
0
Views:
10
Recommended replacement interval for the part category Brake pad set : 30000 km
Important!
This replacement procedure can be used for:
MERCEDES-BENZ E-Class Platform / Chassis (VF211) E 220 CDI (211.608), MERCEDES-BENZ E-Class Platform / Chassis (VF211) E 220 CDI (211.606) … View more
The steps may slightly vary depending on the car design.
MERCEDES-BENZ E-Class Platform / Chassis (VF211) E 220 CDI (211.608), MERCEDES-BENZ E-Class Platform / Chassis (VF211) E 220 CDI (211.606) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Brake Pads for E-Class Platform / Chassis (VF211) and other MERCEDES-BENZ models
Alternative products

Wire brush
Nylon cleaning brush
WD-40 spray
Brake cleaner
Anti-squeal paste
Copper grease
Torque wrench
Combination spanner #17
Drive socket # 13
Wheel impact socket #17
Brake caliper wind back tool
Ratchet wrench
Crow bar
Round-nose pliers
Wheel chock
Replacement: brake pads – MERCEDES-BENZ E-Klasse Pritsche / Fahrgestell (VF211). AUTODOC recommends:
- Perform the replacement of brake pads in complete set for each axis. This provides effective braking.
- The replacement procedure is identical for all brake pads on the same axle.
- Please note: all work on the car – MERCEDES-BENZ E-Klasse Pritsche / Fahrgestell (VF211)– should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Open the bonnet.Step 2Connect the service equipment and switch the SBC system to service mode.Please note!Some vehicles may not have the SBC system.Step 3
Unscrew the brake fluid reservoir cap. - Step 4Secure the wheels with chocks.Step 5
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 6Raise the front of the car and secure on supports.Step 7
Unscrew the wheel bolts.AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. MERCEDES-BENZ E-Klasse Pritsche / Fahrgestell (VF211) - Step 8
Remove the wheel. - Step 9
Detach the connector of the brake pad wear sensor. Use round-nose pliers. - Step 10
Spread the brake pads. Use a crowbar. - Step 11
Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray. - Step 12
Unscrew the brake caliper fastening. Use a combination spanner #17. Use a drive socket #13. Use a ratchet wrench. - Step 13
Remove the brake caliper.Replacement: brake pads – MERCEDES-BENZ E-Klasse Pritsche / Fahrgestell (VF211). Tip from AUTODOC experts:Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary. - Step 14
Treat the brake caliper piston. Use a nylon cleaning brush. Use a brake cleaner.AUTODOC recommends:Replacement: brake pads – MERCEDES-BENZ E-Klasse Pritsche / Fahrgestell (VF211). After applying the spray, wait a few minutes. - Step 15
Install the brake caliper wind back tool. - Step 16
Remove the brake pads.Replacement: brake pads – MERCEDES-BENZ E-Klasse Pritsche / Fahrgestell (VF211). Tip from AUTODOC:Measure the brake disc thickness. Upon reaching the wear limit the part must be replaced. - Step 17Disconnect the brake pads wear sensor.Step 18
Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.AUTODOC recommends:Replacement: brake pads – MERCEDES-BENZ E-Klasse Pritsche / Fahrgestell (VF211). After applying the spray, wait a few minutes. - Step 19
Treat the brake pads in the area where their surface comes into contact with the brake caliper bracket. Use anti-squeal paste.Replacement: brake pads – MERCEDES-BENZ E-Klasse Pritsche / Fahrgestell (VF211). Tip from AUTODOC:Make sure the disc surface is clean before installing the pads.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the MERCEDES-BENZ E-Class Platform / Chassis (VF211) model
Popular maintenance tutorials for MERCEDES-BENZ E-Klasse Pritsche / Fahrgestell (VF211)
Complete guides for changing the Brake pad set on different MERCEDES-BENZ E-CLASS models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your MERCEDES-BENZ E-Class Platform / Chassis (VF211)
View more
Petrol or diesel: The engine showdown! | AUTODOC
Why does it burn oil? The main cause of oil consumption in EA888 Gen 1
Top 4 Car Cleaning Products to Protect Your Car's Body | AUTODOC Tips
When, why, and how to change engine oil | AUTODOC tips
Most commonly replaced car parts on MERCEDES-BENZ E-CLASS
Time to replace parts? Get even better deals in our Shop app.

SCAN ME

































