Disclaimer
How to change front anti roll bar links on TOYOTA Avensis Verso (M2) – replacement guide
downloads:
0
Views:
7
Important!
This replacement procedure can be used for:
TOYOTA Avensis Verso (_M2_) 2.4 VVT-i 4WD (ACM26_) … View more
The steps may slightly vary depending on the car design.
TOYOTA Avensis Verso (_M2_) 2.4 VVT-i 4WD (ACM26_) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for Avensis Verso (_M2_) and other TOYOTA models
Anti-roll bar link
Alternative products
Anti-roll bar link
Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #17
Combination spanner #19
Drive socket # 17
Drive socket # 19
HEX bit no.H6
Wheel impact socket #21
Ratchet wrench
Torque wrench
Crow bar
Wheel chock
AUTODOC recommends:
- Replace the stabiliser links on TOYOTA AVENSIS VERSO (_CLM2_, _ACM2_) in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- All work should be done with the engine stopped.
Replacement: anti roll bar links – TOYOTA AVENSIS VERSO (_CLM2_, _ACM2_). Recommended sequence of steps:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #21. - Step 3Raise the front of the car and secure on supports.Step 4
Unscrew the wheel bolts.Replacement: anti roll bar links – TOYOTA AVENSIS VERSO (_CLM2_, _ACM2_). Tip from AUTODOC experts:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 5
Remove the wheel. - Step 6
Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use HEX No.H6. Use a combination spanner #17. - Step 8
Unscrew the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #17. Use a drive socket #17. Use a ratchet wrench. - Step 9
Remove the stabilizer rod. Use a crowbar.Replacement: anti roll bar links – TOYOTA AVENSIS VERSO (_CLM2_, _ACM2_). Tip from AUTODOC experts:Examine stabiliser bushes. Replace them if needed. - Step 10Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.Step 11
Install a new rod, tighten the fasteners. Use a combination spanner #19. Use a drive socket #19. Use HEX No.H6. Use a ratchet wrench.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the TOYOTA Avensis Verso (M2) model
Popular maintenance tutorials for Toyota Avensis Verso M2
Free download PDF
4.33 MB
Free download PDF1.68 MB
Free download PDF696.32 KB
Free download PDF542.72 KB
Free download PDF1.72 MB
Free download PDF860.16 KB
Complete guides for changing the Drop links on different TOYOTA AVENSIS models
Free download PDF1.27 MB
Free download PDF1.25 MB
Free download PDF1.27 MB
Free download PDF1.25 MB
Free download PDF1.25 MB
Free download PDF972.8 KB
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your TOYOTA Avensis Verso (_M2_)
View more
Top 5 car noises you shouldn't ignore
5 causes of turbocharger failure and how to avoid them
DIY brake caliper restoration | AUTODOC tips
How to Fix P0401 ✅ error code Insufficient EGR flow
Most commonly replaced car parts on TOYOTA AVENSIS
Time to replace parts? Get even better deals in our Shop app.
SCAN ME