Disclaimer
How to change front anti roll bar links on MAZDA 5 (CR19) – replacement guide
downloads:
3
Views:
36
Important!
This replacement procedure can be used for:
MAZDA 5 (CR19) 2.0 CD (CR19), MAZDA 5 (CR19) 2.0 CD (CR19), MAZDA 5 (CR19) 2.0 (CREW), MAZDA 5 (CR19) 1.8 (CR19) … View more
The steps may slightly vary depending on the car design.
MAZDA 5 (CR19) 2.0 CD (CR19), MAZDA 5 (CR19) 2.0 CD (CR19), MAZDA 5 (CR19) 2.0 (CREW), MAZDA 5 (CR19) 1.8 (CR19) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for 5 (CR19) and other MAZDA models
Anti-roll bar link
Alternative products
Anti-roll bar link
Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #15
Drive socket # 14
Wheel impact socket #19
Ratchet wrench
Torque wrench
Wheel chock
AUTODOC recommends:
- Replace the stabiliser links on MAZDA 5 (CR19) in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- Please note: all work on the car – MAZDA 5 (CR19) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #19. - Step 3Raise the front of the car and secure on supports.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. MAZDA 5 (CR19) - Step 5
Remove the wheel. - Step 6Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.Step 7
Unscrew the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #15. Use a drive socket #14. Use a ratchet wrench. - Step 8
Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #15 (2 pieces). - Step 9
Remove the stabilizer rod.Replacement: anti roll bar links – MAZDA 5 (CR19). Professionals recommend:Examine stabiliser bushes. Replace them if needed. - Step 10Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.Step 11
Install a new rod, tighten the fasteners.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the MAZDA 5 (CR19) model
Popular maintenance tutorials for Mazda 5 cr19
Free download PDF
1.73 MB
Free download PDF2.22 MB
Free download PDF1.31 MB
Free download PDF1.85 MB
Free download PDF1.64 MB
Free download PDF2.32 MB
Complete guides for changing the Drop links on different MAZDA 5 models
Free download PDF1.1 MB
Free download PDF972.8 KB
Free download PDF1.16 MB
Free download PDF1.11 MB
Free download PDF1.99 MB
Free download PDF1.61 MB
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your MAZDA 5 (CR19)
View more
DIY rear axle restoration | Drivetrain restoration – Part 2
#DIY Tips for Fixing Your Car's Air Conditioning Issues | Don't Wait for Costly Repairs!
#DIY Guide: How to Fix a Cracked Windscreen Without a Garage Visit
Fuse Replacement Made Simple: Step-by-Step Guide | AUTODOC
Most commonly replaced car parts on MAZDA 5
Time to replace parts? Get even better deals in our Shop app.
SCAN ME