
Disclaimer
How to change front anti roll bar links on ALPINA RLE Roadster (Z1) – replacement guide
downloads:
0
Views:
2
Important!
This replacement procedure can be used for:
ALPINA RLE Roadster (Z1) 2.7 … View more
The steps may slightly vary depending on the car design.
ALPINA RLE Roadster (Z1) 2.7 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for RLE Roadster (Z1) and other ALPINA models
Anti-roll bar link
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Torque wrench
Combination spanner #13
Combination spanner #16
Combination spanner #17
Drive socket # 13
Drive socket # 16
Drive socket # 17
Wheel impact socket #17
Ratchet wrench
Hydraulic transmission jack
Wheel chock
AUTODOC recommends:
- Replace the stabiliser links on ALPINA RLE Roadster (Z1) in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- Please note: all work on the car – ALPINA RLE Roadster (Z1) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Secure the wheels with chocks.Step 2Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 3Raise the front of the car and secure on supports.Step 4Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. ALPINA RLE Roadster (Z1)
- Step 5Remove the wheel.
- Step 6Clean all joints of the stabiliser link. Use a wire brush. Use WD-40 spray.
- Step 7Unscrew the fastener connecting the stabilizer bar with the control arm. Use a combination spanner #13. Use a drive socket #13. Use a ratchet wrench.
- Step 8Remove the fastening bolt.
- Step 9Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #16. Use a drive socket #16. Use a ratchet wrench.
- Step 10Remove the stabilizer rod.Replacement: anti roll bar links – ALPINA RLE Roadster (Z1). AUTODOC experts recommend:Examine the stabiliser bushes. Replace them if necessary.
- Step 11Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
- Step 12Ιnstall the transverse stabilizer link.
- Step 13Install the fastening bolt.Step 14Tighten the stabiliser link fastener. Use a combination spanner #17. Use a drive socket #17. Use a ratchet wrench.
- Step 15Support the arm. Use a hydraulic transmission jack.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the ALPINA RLE Roadster (Z1) model
Popular maintenance tutorials for ALPINA RLE Roadster (Z1)
Complete guides for changing the Drop links on different ALPINA RLE models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your ALPINA RLE Roadster (Z1)
View more
- Top 7 Manual Transmission Mistakes to Avoid | AUTODOC Tips
- The Fast and Easy Way to Fix a Broken Wheel Stud | AUTODOC tips
- What to do if the ABS light comes on: DIY Diagnostics Tips
- 5 Ways You’re Scrubbing Your Car Wrong | AUTODOC Tips
Most commonly replaced car parts on ALPINA RLE
Time to replace parts? Get even better deals in our Shop app.

SCAN ME