Disclaimer
How to change engine oil and filter on VW Transporter T3 Van – replacement guide
downloads:
11
Views:
308
Recommended replacement interval for the part category Oil filter : 7500 km
Important!
This replacement procedure can be used for:
VW Transporter T3 Van 1.6 D, VW Transporter T3 Van 1.6 TD Syncro, VW Transporter T3 Van 1.7 D, VW Transporter T3 Van 1.6 TD … View more
The steps may slightly vary depending on the car design.
VW Transporter T3 Van 1.6 D, VW Transporter T3 Van 1.6 TD Syncro, VW Transporter T3 Van 1.7 D, VW Transporter T3 Van 1.6 TD … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Oil Filter for Transporter T3 Van and other VW models
Alternative products

Wire brush
All-purpose cleaning spray
Torque wrench
Drive socket # 19
Ratchet wrench
Chain oil filter wrench
Funnel
Oil drain pan
Fender cover
AUTODOC recommends:
- Replace the oil filter every time when changing motor oil.
- All work should be done with the engine stopped.
- Wear gloves to prevent contact with hot liquid.
Replacement: engine oil and filter – VW TRANSPORTER III Box. Take the following steps:
- Step 1Open the hood.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3
Unscrew the oil filler plug. - Step 4Lift the car using a jack or place it over an inspection pit.AUTODOC recommends:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.All work should be done with the engine stopped.Step 5
Put a waste oil container with at least 5 l capacity under the drainage hole. - Step 6Clean the area of the oil pan drainage hole. Use a wire brush. Use all-purpose cleaning spray.Step 7
Unscrew the drain plug. Use a drive socket #19. Use a ratchet wrench. - Step 8
Drain the used oil.AUTODOC recommends:Caution! The oil may be hot. - Step 9Prepare a container for the old oil filter.Step 10Clean the oil filter. Use all-purpose cleaning spray.Step 11
Unscrew the oil filter. Use a chain oil filter wrench. - Step 12
Put the old oil filter in the container.Replacement: engine oil and filter – VW TRANSPORTER III Box. AUTODOC recommends:Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter. - Step 13
Clean the oil filter seat. Use all-purpose cleaning spray. - Step 14
Lubricate the rubber seal of the new filter with a little amount of fresh oil. - Step 15
Screw the new filter into its place. Use a torque wrench. Tighten it to 23 Nm torque.AUTODOC recommends:Wait until the oil has completely drained from the drainage hole. - Step 16
Clean the area of the oil pan drainage hole. - Step 17
Screw in the new drainage plug and tighten it. Use a drive socket #19. Use a torque wrench. Tighten it to 28 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VW Transporter T3 Van model
Popular maintenance tutorials for VW T3 Van
Complete guides for changing the Oil filters on different VW TRANSPORTER models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VW Transporter T3 Van
View more
Deep interior cleaning | Car transformation by detailing
The Fast and Easy Way to Fix a Broken Wheel Stud | AUTODOC tips
Transform Your Old Engine Valve Cover: Quick Polishing Tips for a Shiny Finish | AUTODOC Tips
How do EGR valves work? | AUTODOC
Most commonly replaced car parts on VW TRANSPORTER
Time to replace parts? Get even better deals in our Shop app.

SCAN ME




























