
Disclaimer
How to change engine oil and filter on SUZUKI SX4 Saloon (GY) – replacement guide
downloads:
3
Views:
196

Recommended replacement interval for the part category Oil filter : 1 year / 15000 km
Important!
This replacement procedure can be used for:
SUZUKI SX4 Saloon (GY) 1.6 AWD (RW 416), SUZUKI SX4 Saloon (GY) 1.6 (RW 416), SUZUKI SX4 Saloon (GY) 1.6 (RW 416) … View more
The steps may slightly vary depending on the car design.
SUZUKI SX4 Saloon (GY) 1.6 AWD (RW 416), SUZUKI SX4 Saloon (GY) 1.6 (RW 416), SUZUKI SX4 Saloon (GY) 1.6 (RW 416) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Oil Filter for SX4 Saloon (GY) and other SUZUKI models
Oil filter
Alternative products

All-purpose cleaning spray
Drive socket # 17
Oil filter cup socket 65/14F
Ratchet wrench
Torque wrench
Funnel
Oil drain pan
Fender cover
Replacement: engine oil and filter – SUZUKI SX4 Saloon (GY). AUTODOC experts recommend:
- Replace the oil filter every time when changing motor oil.
- Wear gloves to prevent contact with hot liquid.
- Please note: all work on the car – SUZUKI SX4 Saloon (GY) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Lift the car using a jack or place it over an inspection pit.Replacement: engine oil and filter – SUZUKI SX4 Saloon (GY). Professionals recommend:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.All work should be done with the engine stopped.
- Step 2Put a waste oil container with at least 4 l capacity under the drainage hole.Step 3Unscrew the drain plug. Use a drive socket #17. Use a ratchet wrench.
- Step 4Drain the used oil.Replacement: engine oil and filter – SUZUKI SX4 Saloon (GY). Tip:Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole.
- Step 5Clean the area of the oil pan drainage hole.
- Step 6Screw in the new drainage plug and tighten it. Use a drive socket #17. Use a torque wrench. Tighten it to 28 nm torque.
- Step 7Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray.Step 8Unscrew the oil filter. Use the 65/14F socket. Use a ratchet wrench.
- Step 9Put the old oil filter in the container.
- Step 10Clean the oil filter seat.Step 11Screw the new filter into its place. Use the 65/14F socket. Use a torque wrench. Tighten it to 15 Nm torque.
- Step 12Lower the car.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the SUZUKI SX4 I Saloon (GY) model
Popular maintenance tutorials for Suzuki SX4 Saloon
Complete guides for changing the Oil filters on different SUZUKI SX4 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your SUZUKI SX4 Saloon (GY)
View more
- How I started restoring a driveshaft | Drivetrain restoration – Part 1
- What to do if your check engine light is on | AUTODOC tips
- TOP 6 WD-40 lifehacks | AUTODOC tips
- Fuse Replacement Made Simple: Step-by-Step Guide | AUTODOC
Most commonly replaced car parts on SUZUKI SX4
Time to replace parts? Get even better deals in our Shop app.

SCAN ME