Disclaimer
How to change engine oil and filter on SEAT Inca (6K9) – replacement guide
downloads:
3
Views:
49
Recommended replacement interval for the part category Oil filter : 1 year / 15000 km
Important!
This replacement procedure can be used for:
SEAT Inca (6K9) 1.4 16V, SEAT Inca (6K9) 1.4 i … View more
The steps may slightly vary depending on the car design.
SEAT Inca (6K9) 1.4 16V, SEAT Inca (6K9) 1.4 i … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Oil Filter for Inca (6K9) and other SEAT models
Alternative products

Wire brush
All-purpose cleaning spray
Torque wrench
Drive socket # 19
Drive socket # 30
Ratchet wrench
Oil drain pan
Funnel
Fender cover
Replacement: engine oil and filter – SEAT INCA (6K9). AUTODOC recommends:
- Replace the oil filter every time when changing motor oil.
- Wear gloves to prevent contact with hot liquid.
- All work should be done with the engine stopped.
Replacement: engine oil and filter – SEAT INCA (6K9). Take the following steps:
- Step 1Open the hood.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3
Unscrew the oil filler plug. - Step 4Lift the car using a jack or place it over an inspection pit.AUTODOC recommends:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.Step 5
Put a waste oil container with at least 4 l capacity under the drainage hole. - Step 6
Clean the area of the oil pan drainage hole. Use a wire brush. Use all-purpose cleaning spray. - Step 7
Unscrew the drain plug. Use a drive socket #19. Use a ratchet wrench. - Step 8
Drain the used oil.Replacement: engine oil and filter – SEAT INCA (6K9). Tip:Caution! The oil may be hot. - Step 9
Clean the oil filter. Use all-purpose cleaning spray. - Step 10Prepare a container for the old oil filter.Step 11
Unscrew the oil filter. Use a drive socket #30. Use a ratchet wrench. - Step 12
Put the old oil filter in the container.Replacement: engine oil and filter – SEAT INCA (6K9). Tip from AUTODOC:Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter. - Step 13
Clean the oil filter seat. Use all-purpose cleaning spray. - Step 14
Lubricate the rubber seal of the new filter with a little amount of fresh oil. - Step 15
Screw the new filter into its place. Use a drive socket #30. Use a torque wrench. Tighten it to 26 Nm torque.AUTODOC recommends:Wait until the oil has completely drained from the drainage hole. - Step 16
Clean the area of the oil pan drainage hole. - Step 17
Screw in the new drainage plug and tighten it. Use a drive socket #19. Use a torque wrench. Tighten it to 27 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the SEAT Inca (6K9) model
Popular maintenance tutorials for Seat Inca 6K9
Complete guides for changing the Oil filters on different SEAT INCA models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your SEAT Inca (6K9)
View more
Cold starts | 5 mistakes that wreck your car
How to get your motorcycle ready for spring
Transform Your Old Engine Valve Cover: Quick Polishing Tips for a Shiny Finish | AUTODOC Tips
Prevent Engine Damage: How to Identify Rocker Cover Gasket Issues and Proper Replacement | AUTODOC
Most commonly replaced car parts on SEAT INCA
Time to replace parts? Get even better deals in our Shop app.

SCAN ME
































