
Disclaimer
How to change engine oil and filter on SEAT Exeo ST (3R5) – replacement guide
downloads:
13
Views:
246

Recommended replacement interval for the part category Oil filter : 12 month / 15000 km
Important!
This replacement procedure can be used for:
SEAT Exeo ST (3R5) 2.0 TFSI, SEAT Exeo ST (3R5) 2.0 TFSI … View more
The steps may slightly vary depending on the car design.
SEAT Exeo ST (3R5) 2.0 TFSI, SEAT Exeo ST (3R5) 2.0 TFSI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Oil Filter for Exeo ST (3R5) and other SEAT models
Oil filter
Alternative products

Wire brush
All-purpose cleaning spray
Torque wrench
Drive socket # 19
Drive socket # 36
Ratchet wrench
Oil drain pan
Funnel
Fender cover
Replacement: engine oil and filter – SEAT EXEO ST (3R5). AUTODOC experts recommend:
- Replace the oil filter every time when changing motor oil.
- Wear gloves to prevent contact with hot liquid.
- Please note: all work on the car – SEAT EXEO ST (3R5) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Open the hood.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3Unscrew the oil filler plug.
- Step 4Pull up the oil dipstick.
- Step 5Lift the car using a jack or place it over an inspection pit.Replacement: engine oil and filter – SEAT EXEO ST (3R5). AUTODOC experts recommend:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.Step 6Put a waste oil container with at least 5 l capacity under the drainage hole.
- Step 7Clean the area of the oil pan drainage hole. Use a wire brush. Use all-purpose cleaning spray.
- Step 8Unscrew the drain plug. Use a drive socket #19. Use a ratchet wrench.
- Step 9Drain the used oil.Replacement: engine oil and filter – SEAT EXEO ST (3R5). AUTODOC recommends:Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole.
- Step 10Clean the oil filter housing cap. Use all-purpose cleaning spray.
- Step 11Unscrew the filter housing cap together with the old filter element. Use a drive socket #36. Use a ratchet wrench.
- Step 12Put the old oil filter in the container.
- Step 13Detach the oil filter from the filter cover.
- Step 14Remove the oil filter cover O-ring.
- Step 15Clean the oil filter housing cap. Use all-purpose cleaning spray.
- Step 16Install a new O-ring to its mounting seat on the filter cover.
- Step 17Install the new oil filter to the mounting seat on the filter cover.
- Step 18Clean the oil filter seat. Use all-purpose cleaning spray.
- Step 19Install a new oil filter housing cover and tighten it. Use a drive socket #36. Use a torque wrench. Tighten it to 25 Nm torque.
- Step 20Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray.
- Step 21Screw in the new drainage plug and tighten it. Use a drive socket #19. Use a torque wrench. Tighten it to 27 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the SEAT Exeo ST (3R5) model
Popular maintenance tutorials for Seat Exeo st
Complete guides for changing the Oil filters on different SEAT EXEO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your SEAT Exeo ST (3R5)
View more
- 5 more brake repair mistakes | Stop making these brake repair mistakes
- Engine Overheating? Replace Your Cooling Fan to Fix It
- Transform Your Car's Look: 6 Simple Accessories You Need to Try!
- DIY car soundproofing | AUTODOC tips
Most commonly replaced car parts on SEAT EXEO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME