Disclaimer
How to change CV joint on VW Golf VII Variant (BA5, BV5) – replacement guide
downloads:
1
Views:
13
Important!
This replacement procedure can be used for:
VW Golf VII Variant (BA5, BV5) 1.6 TDI, VW Golf VII Variant (BA5, BV5) 1.4 TGI CNG, VW Golf VII Variant (BA5, BV5) 1.2 TSI, VW Golf VII Variant (BA5, BV5) 1.2 TSI, VW Golf VII Variant (BA5, BV5) 1.4 TSI MultiFuel, VW Golf VII Variant (BA5, BV5) 1.2 TSI, VW Golf VII Variant (BA5, BV5) 1.4 TSI MultiFuel, VW Golf VII Variant (BA5, BV5) 1.6 … View more
The steps may slightly vary depending on the car design.
VW Golf VII Variant (BA5, BV5) 1.6 TDI, VW Golf VII Variant (BA5, BV5) 1.4 TGI CNG, VW Golf VII Variant (BA5, BV5) 1.2 TSI, VW Golf VII Variant (BA5, BV5) 1.2 TSI, VW Golf VII Variant (BA5, BV5) 1.4 TSI MultiFuel, VW Golf VII Variant (BA5, BV5) 1.2 TSI, VW Golf VII Variant (BA5, BV5) 1.4 TSI MultiFuel, VW Golf VII Variant (BA5, BV5) 1.6 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – CV Joint for Golf VII Variant (BA5, BV5) and other VW models
Alternative products

Wire brush
WD-40 spray
All-purpose cleaning spray
Brake cleaner
Copper grease
Torque wrench
Drive socket # 16
Drive socket # 19
Drive socket # 27
Wheel impact socket #17
Ratchet wrench
Tap wrench
Bush and bearing driver set
Flat screwdriver
Clic-R collar pliers
Hammer
CV joint puller
Crow bar
Hydraulic transmission jack
Wheel chock
Replacement: CV joint – VW GOLF VII Estate (BA5). Tip from AUTODOC:
- The CV joint replacement procedure is identical for the left and right CV axles.
- Replace the CV joints of CV axles in pairs.
- Please note: all work on the car – VW GOLF VII Estate (BA5) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Secure the wheels with chocks.Step 2
Loosen the fastener of the driveshaft. Use a drive socket #27. Use a tap wrench. - Step 3
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 4Raise the front of the car and secure on supports.Step 5
Unscrew the wheel bolts.AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. VW GOLF VII Estate (BA5) - Step 6
Remove the wheel. - Step 7
Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray. - Step 8
Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #19. Use a ratchet wrench. - Step 9
Remove the stabilizer rod. - Step 10Remove the fastening bolt.Step 11
Clean the fasteners connecting the ball joint to the suspension control arm. Use a wire brush. Use WD-40 spray. - Step 12
Unscrew the fastener connecting the ball joint to the suspension control arm. Use a drive socket #16. Use a ratchet wrench. - Step 13
Disconnect the spherical joint from the arm. - Step 14
Detach the driveshaft from the steering knuckle.Replacement: CV joint – VW GOLF VII Estate (BA5). Professionals recommend:Make sure that the drive shaft is not unloaded (when the car is jacked). - Step 15
Prop up the steering knuckle. Use a hydraulic transmission jack. - Step 16
Clean the clamps of the CV joint boot. Use a wire brush. Use WD-40 spray. - Step 17
Detach the clamps of the CV joint boot. Use a crowbar. - Step 18
Detach the CV joint boot. - Step 19
Attach the CV joint puller. - Step 20
Install and tighten the drive shaft bolt. Use a drive socket #27. Use a ratchet wrench. - Step 21Detach the CV joint. Use a CV joint puller.Step 22
Unscrew the fastener connecting the drive shaft to the wheel hub. - Step 23
Remove the fastening bolt. - Step 24
Remove the CV joint together with its boot. - Step 25
Clean the CV joint mounting seat. Use all-purpose cleaning spray. - Step 26
Remove the CV joint circlip. Use a flat screwdriver. - Step 27
Clean the splines of the drive shaft CV joint. Use a wire brush. Use all-purpose cleaning spray. - Step 28
Install the CV joint boot on the CV axle. - Step 29
Install the CV joint circlip. - Step 30
Pack the CV joint with the grease supplied in the kit. - Step 31
Move the inner race of the new CV joint from side to side to get it ready to work. - Step 32
Install the new CV joint. Use a bush and bearing driver set. Use a hammer.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VW Golf VII Variant (BA5, BV5) model
Popular maintenance tutorials for Golf BA5
Complete guides for changing the Constant velocity joint on different VW GOLF models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VW Golf VII Variant (BA5, BV5)
View more
How to Use Sandblasting Equipment: Step-by-Step Guide | AUTODOC Tips
Understanding Car Tools: The Key Differences You Need to Know | AUTODOC tips
DIY manual gearbox restoration | Drivetrain restoration – Part 3
#DIY Tips for Fixing Your Car's Air Conditioning Issues | Don't Wait for Costly Repairs!
Most commonly replaced car parts on VW GOLF
Time to replace parts? Get even better deals in our Shop app.

SCAN ME




































