
Disclaimer
How to change track rod end on SEAT Alhambra (710, 711) – replacement guide
downloads:
0
Views:
5
Important!
This replacement procedure can be used for:
SEAT Alhambra (710, 711) 1.4 TSI, SEAT Alhambra (710, 711) 2.0 TDI, SEAT Alhambra (710, 711) 2.0 TDI, SEAT Alhambra (710, 711) 2.0 TSI, SEAT Alhambra (710, 711) 2.0 TDI, SEAT Alhambra (710, 711) 2.0 TDI 4Drive, SEAT Alhambra (710, 711) 2.0 TDI, SEAT Alhambra (710, 711) 2.0 TDI, SEAT Alhambra (710, 711) 1.8 TSI … View more
The steps may slightly vary depending on the car design.
SEAT Alhambra (710, 711) 1.4 TSI, SEAT Alhambra (710, 711) 2.0 TDI, SEAT Alhambra (710, 711) 2.0 TDI, SEAT Alhambra (710, 711) 2.0 TSI, SEAT Alhambra (710, 711) 2.0 TDI, SEAT Alhambra (710, 711) 2.0 TDI 4Drive, SEAT Alhambra (710, 711) 2.0 TDI, SEAT Alhambra (710, 711) 2.0 TDI, SEAT Alhambra (710, 711) 1.8 TSI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Track Rod End for Alhambra (710, 711) and other SEAT models
Track rod end
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #23
Combination spanner #24
Drive socket # 18
Drive socket # 19
Wheel impact socket #17
Ratchet wrench
Torque wrench
Tap wrench
Vernier caliper
Ball joint puller
Wheel chock
Replacement: track rod end – SEAT ALHAMBRA (710, 711). AUTODOC recommends:
- Replace tie rod ends in pairs.
- The replacement procedure is identical for the right and left tie rod ends.
- All work should be done with the engine stopped.
Replacement: track rod end – SEAT ALHAMBRA (710, 711). Take the following steps:
- Step 1Secure the wheels with chocks.
- Step 2Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 3Raise the front of the car and secure on supports.Step 4Unscrew the wheel bolts.Replacement: track rod end – SEAT ALHAMBRA (710, 711). Tip:To avoid injury, hold up the wheel when unscrewing the bolts.
- Step 5Remove the wheel.
- Step 6Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.
- Step 7Unscrew the end fastening nut to the steering knuckle. Use a drive socket #18. Use a tap wrench.
- Step 8When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper.
- Step 9Loosen the lock nut securing the tie rod end to the tie rod. Use a combination spanner #23. Use a combination spanner #24.
- Step 10Disconnect the tie rod end from the steering knuckle. Use a ball joint puller.
- Step 11Screw the end out of the tie rod.
- Step 12Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray.
- Step 13Screw on a new tie rod end.Replacement: track rod end – SEAT ALHAMBRA (710, 711). AUTODOC experts recommend:While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements.
- Step 14Connect the tie rod end to the steering knuckle.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the SEAT Alhambra II (710, 711) model
Popular maintenance tutorials for SEAT Alhambra 7N
Complete guides for changing the Tie rod end on different SEAT ALHAMBRA models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your SEAT Alhambra (710, 711)
View more
- Checking the starter without removing it | AUTODOC tips
- How to tighten cylinder head bolts
- Top 7 signs of a bad starter
- K2 ROTON wheel cleaner overview
Most commonly replaced car parts on SEAT ALHAMBRA
Time to replace parts? Get even better deals in our Shop app.

SCAN ME