Disclaimer
How to change rear wheel bearing on VW Polo Saloon (9N4) – replacement guide
downloads:
0
Views:
4
Important!
This replacement procedure can be used for:
VW Polo Saloon (9N4) 1.9 TDI … View more
The steps may slightly vary depending on the car design.
VW Polo Saloon (9N4) 1.9 TDI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Wheel Bearing for Polo Saloon (9N4) and other VW models
Alternative products

Wire brush
WD-40 spray
All-purpose cleaning spray
Copper grease
Torque wrench
Combination spanner #10
12-point socket #30
Torx bit T30
Wheel impact socket #17
Ratchet wrench
Hammer
Tap wrench
Crow bar
Rubber mallet
Wheel chock
Replacement: wheel bearing – VW POLO Saloon (9N4). AUTODOC experts recommend:
- Do not re-use the bearing assembly of your VW POLO Saloon (9N4) car.
- The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
- All work should be done with the engine stopped.
Replacement: wheel bearing – VW POLO Saloon (9N4). Recommended sequence of steps:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the rear of the car and secure on supports.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VW POLO Saloon (9N4) - Step 5
Remove the wheel. - Step 6
Clean the brake drum fasteners. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the brake drum fastening. Use Torx T30. Use a ratchet wrench. - Step 8
Open the car door. - Step 9
Remove the parking brake lever trim cover. - Step 10
Loosen the parking brake cable. Use a combination spanner #10. - Step 11
Remove the brake drum.Replacement: wheel bearing – VW POLO Saloon (9N4). Tip from AUTODOC:Examine the brake drum. Replace it if necessary. - Step 12
Remove the hub bearing protection cap. Use a crowbar. Use a hammer.AUTODOC recommends:Some cars are not equipped with wheel hub caps. - Step 13
Unscrew the wheel hub axle nut. Use 12-point socket No.30. Use a tap wrench. - Step 14
Remove the hub and the bearing together, since they are a sealed unit. - Step 15
Clean the hub bearing mounting seat. Use all-purpose cleaning spray. - Step 16
Install the new wheel hub with a bearing. - Step 17
Tighten the hub. Use 12-point socket No.30. Use a torque wrench. Tighten it to 175 nm torque.Replacement: wheel bearing – VW POLO Saloon (9N4). Professionals recommend:The wheel bearing unit must not tilt on the axle pin. - Step 18
Install the hub bearing protection cap. Use a rubber mallet.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VW Polo IV Saloon (9N4) model
Popular maintenance tutorials for VW Polo 9n Saloon
Complete guides for changing the Wheel bearings on different VW POLO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VW Polo Saloon (9N4)
View more
TOP 6 WD-40 lifehacks | AUTODOC tips
5 possible reasons why your car heater isn't working
How to make an injector test bench yourself
Regain Your Confidence on the Road: Easy Headlight Restoration Tips
Most commonly replaced car parts on VW POLO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME
































