How to change rear upper arm on BMW 1 Hatchback (E87) – replacement guide
BMW 1 Hatchback (E87) 116i, BMW 1 Hatchback (E87) 116i, BMW 1 Hatchback (E87) 116 i, BMW 1 Hatchback (E87) 118 i, BMW 1 Hatchback (E87) 118 i, BMW 1 Hatchback (E87) 118 i, BMW 1 Hatchback (E87) 120i, BMW 1 Hatchback (E87) 120i, BMW 1 Hatchback (E87) 120i, BMW 1 Hatchback (E87) 120i, BMW 1 Hatchback (E87) 130i, BMW 1 Hatchback (E87) 130i, BMW 1 Hatchback (E87) 116d, BMW 1 Hatchback (E87) 118d, BMW 1 Hatchback (E87) 118d, BMW 1 Hatchback (E87) 118d, BMW 1 Hatchback (E87) 120d, BMW 1 Hatchback (E87) 120d, BMW 1 Hatchback (E87) 123d, BMW 1 Hatchback (E87) 116 d, BMW 1 Hatchback (E87) 118 i, BMW 1 Hatchback (E87) 120d … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle

- The replacement procedure is identical for the right and left upper control arms.
- Please note: all work on the car – BMW 1 (E87) – should be done with the engine switched off.
- Step 1

Secure the wheels with chocks.
- Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 3
Raise the rear of the car and secure on supports.
Step 4
Unscrew the wheel bolts.
AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. BMW 1 (E87)
- Step 5

Remove the wheel.
- Step 6
Clean all joints of the arm. Use a wire brush. Use WD-40 spray.
Step 7
Unscrew the fastener connecting the control arm to the rear knuckle. Use a drive socket #18. Use a tap wrench. Use a ratchet wrench.
- Step 8
Remove the fastening bolt.
Step 9
Detach the suspension arm from the rear knuckle.
- Step 10
Disconnect the ABS sensor wiring. Use a flat screwdriver.
Step 11
Unscrew the arm fastening to the beam. Use a combination spanner #18 (2 pieces).
- Step 12
Remove the rear fastener of the control arm.
Step 13
Remove the rear upper arm.
- Step 14

Clean the mounting seats and the thread of the suspension arm. Use a wire brush. Use WD-40 spray.
- Step 15

Mount the rear upper arm.
Replacement: rear upper arm – BMW 1 (E87). AUTODOC experts recommend:During the installation process, use only new bolts and nuts.
- Step 16
Install the rear fastener of the control arm.
Step 17
Tighten the arm fastening to the beam. Use a combination spanner #18 (2 pieces). Use a torque wrench. Tighten it to 100 Nm torque.
AUTODOC recommends:Important! Be sure to use new fasteners.
Find out which tyre and wheel sizes are compatible with the BMW 1 Hatchback (E87) model
Popular maintenance tutorials for BMW E87
Complete guides for changing the Control arm on different BMW 1 SERIES models
Track expenses, manage logs, schedule replacements, and more.
5 mistakes when replacing consumables
DIY alternator repair | AUTODOC tips
5 more brake repair mistakes | Stop making these brake repair mistakes
How to service a used car after buying it
Most commonly replaced car parts on BMW 1 SERIES

































