Disclaimer
How to change rear shock absorbers on AUDI A6 Saloon (4B2, C5) – replacement guide
downloads:
1
Views:
32
Important!
This replacement procedure can be used for:
AUDI A6 Saloon (4B2, C5) 1.8 T, AUDI A6 Saloon (4B2, C5) 2.4, AUDI A6 Saloon (4B2, C5) 1.9 TDI, AUDI A6 Saloon (4B2, C5) 2.5 TDI, AUDI A6 Saloon (4B2, C5) 2.8, AUDI A6 Saloon (4B2, C5) 1.8, AUDI A6 Saloon (4B2, C5) 2.7 T, AUDI A6 Saloon (4B2, C5) 2.4, AUDI A6 Saloon (4B2, C5) 1.8 T, AUDI A6 Saloon (4B2, C5) 2.5 TDI, AUDI A6 Saloon (4B2, C5) 1.9 TDI, AUDI A6 Saloon (4B2, C5) 1.8, AUDI A6 Saloon (4B2, C5) 2.8, AUDI A6 Saloon (4B2, C5) 2.8, AUDI A6 Saloon (4B2, C5) 2.4, AUDI A6 Saloon (4B2, C5) 2.0, AUDI A6 Saloon (4B2, C5) 3.0, AUDI A6 Saloon (4B2, C5) 2.4, AUDI A6 Saloon (4B2, C5) 2.5 TDI, AUDI A6 Saloon (4B2, C5) 1.9 TDI, AUDI A6 Saloon (4B2, C5) 2.4, AUDI A6 Saloon (4B2, C5) 2.5 TDI, AUDI A6 Saloon (4B2, C5) 3.0 … View more
The steps may slightly vary depending on the car design.
AUDI A6 Saloon (4B2, C5) 1.8 T, AUDI A6 Saloon (4B2, C5) 2.4, AUDI A6 Saloon (4B2, C5) 1.9 TDI, AUDI A6 Saloon (4B2, C5) 2.5 TDI, AUDI A6 Saloon (4B2, C5) 2.8, AUDI A6 Saloon (4B2, C5) 1.8, AUDI A6 Saloon (4B2, C5) 2.7 T, AUDI A6 Saloon (4B2, C5) 2.4, AUDI A6 Saloon (4B2, C5) 1.8 T, AUDI A6 Saloon (4B2, C5) 2.5 TDI, AUDI A6 Saloon (4B2, C5) 1.9 TDI, AUDI A6 Saloon (4B2, C5) 1.8, AUDI A6 Saloon (4B2, C5) 2.8, AUDI A6 Saloon (4B2, C5) 2.8, AUDI A6 Saloon (4B2, C5) 2.4, AUDI A6 Saloon (4B2, C5) 2.0, AUDI A6 Saloon (4B2, C5) 3.0, AUDI A6 Saloon (4B2, C5) 2.4, AUDI A6 Saloon (4B2, C5) 2.5 TDI, AUDI A6 Saloon (4B2, C5) 1.9 TDI, AUDI A6 Saloon (4B2, C5) 2.4, AUDI A6 Saloon (4B2, C5) 2.5 TDI, AUDI A6 Saloon (4B2, C5) 3.0 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Shock Absorber for A6 Saloon (4B2, C5) and other AUDI models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Torque wrench
Combination spanner #16
Combination spanner #17
Drive socket # 13
Drive socket # 16
Drive socket # 17
Torx bit T25
Shock absorber socket #DD6
Wheel impact socket #17
Ratchet wrench
Vice
Hydraulic transmission jack
Wheel chock
Replacement: shock absorbers – AUDI A6 (4B2, C5). AUTODOC recommends:
- Both shock absorbers of the rear suspension should be replaced simultaneously.
- The replacement procedure is identical for the left and right shock absorbers of the rear suspension.
- Please note: all work on the car – AUDI A6 (4B2, C5) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Secure the wheels with chocks.Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the rear of the car and secure on supports.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. AUDI A6 (4B2, C5) - Step 5
Remove the wheel. - Step 6
Unscrew and remove the wheel arch cover fasteners. Use Torx T25. - Step 7
Clean the shock absorber fasteners. Use a wire brush. Use WD-40 spray. - Step 8
Support the rear suspension beam. Use a hydraulic transmission jack. - Step 9
Unscrew the lower fastener of the shock absorber. Use a combination spanner #16. Use a drive socket #16. Use a ratchet wrench. - Step 10
Unscrew the upper fastener of the shock absorber. Use a drive socket #13. Use a ratchet wrench.AUTODOC recommends:Important! Hold the shock absorber while unscrewing the fastening bolts. AUDI A6 (4B2, C5) - Step 11
Remove the fastening bolt. - Step 12
Remove the shock absorber. - Step 13
Grip the shock absorber in a vice. - Step 14
Clean the shock absorber rod fastener. Use a wire brush. Use WD-40 spray. - Step 15
Remove the shock absorber piston rod fastening. Use a shock absorber socket DD№6. Use a drive socket #17. Use a ratchet wrench. - Step 16
Remove the shock absorber mount, boot and bump stop.AUTODOC recommends:Replacement: shock absorbers – AUDI A6 (4B2, C5). Carefully inspect the mount, the boot, and the bump stop of the shock absorber. Replace if necessary.Before installing a new shock absorber you should pump it manually 3-5 times. - Step 17
Install the mount, boot and bump stop onto a new shock absorber. - Step 18
Tighten the shock absorber rod nut. Use a shock absorber socket DD№6. Use a combination spanner #17. Use a torque wrench. Tighten it to 25 nm torque. - Step 19
Treat the shock absorber rod fastener. Use copper grease. - Step 20
Release the vice and take out the shock absorber.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the AUDI A6 C5 Saloon (4B2) model
Popular maintenance tutorials for Audi A6 C5 Saloon
Complete guides for changing the Shock absorbers on different AUDI A6 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your AUDI A6 Saloon (4B2, C5)
View more
Three ways to change oil without a lift
Prevent Engine Damage: How to Identify Rocker Cover Gasket Issues and Proper Replacement | AUTODOC
How to repair a bumper yourself | AUTODOC tips
How to Safely Wash Your Car in Winter Without Damage | AUTODOC tips
Most commonly replaced car parts on AUDI A6
Time to replace parts? Get even better deals in our Shop app.

SCAN ME

































