How to change rear brake pads on BMW X5 E53 – replacement guide
downloads:
1
Views:
174
4
Users voted – 1
Recommended replacement interval for the part category Brake pad set : 30000km
Important!
This replacement procedure can be used for:
BMW X5 (E53) 3.0 i,
BMW X5 (E53) 4.4 i,
BMW X5 (E53) 3.0 d,
BMW X5 (E53) 4.6 is,
BMW X5 (E53) 4.4 i,
BMW X5 (E53) 3.0 d,
BMW X5 (E53) 4.8 is,
BMW X5 (E53) 3.0 d
…
View more
The steps may slightly vary depending on the car design.
How to change rear brake pads / rear brake pad set on BMW X5 (E53) [TUTORIAL AUTODOC]
All the parts you need to replace – Brake Pads for X5 (E53) and other BMW models
Replacement: brake pads – BMW X5 E53. Tip from AUTODOC:
Perform the replacement of brake pads in complete set for each axis. This provides effective braking.
The replacement procedure is identical for all brake pads on the same axle.
Please note: all work on the car – BMW X5 E53 – should be done with the engine switched off.
Carry out replacement in the following order:
Step 1
Open the bonnet.
Step 2
Remove the protective cover.
Step 3
Remove the rubber strip.
Step 4
Unscrew the brake fluid reservoir cap.
Step 5
Secure the wheels with chocks.
Step 6
Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 7
Raise the rear of the car and secure on supports.
Step 8
Unscrew the wheel bolts.
Replacement: brake pads – BMW X5 E53. Tip:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 9
Remove the wheel.
Step 10
Spread the brake pads. Use a crowbar.
Step 11
Remove the dust boot caps of the brake caliper guide pins. Use a crowbar.
Step 12
Unscrew the brake caliper fastening. Use HEX No.H7. Use a ratchet wrench.
Step 13
Detach the brake caliper retaining spring. Use a crowbar.
Step 14
Remove the brake caliper.
Replacement: brake pads – BMW X5 E53. AUTODOC experts recommend:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
Step 15
Remove the brake pads. Use a crowbar.
Replacement: brake pads – BMW X5 E53. AUTODOC recommends:
Measure the brake disc thickness. Upon reaching the wear limit the part must be replaced.
Step 16
Remove the connector of the brake pad wear sensor. Use a crowbar.
Please note!
Some cars are not equipped with the brake pad wear sensor.
Step 17
Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.
AUTODOC recommends:
Replacement: brake pads – BMW X5 E53. After applying the spray, wait a few minutes.
Step 18
Press in the brake caliper piston. Use brake caliper wind back tool.
Step 19
Treat the back side of the new brake pads. Use anti-squeal paste.
Replacement: brake pads – BMW X5 E53. Professionals recommend:
Make sure the disc surface is clean before installing the pads.
Step 20
Install new brake pads.
Replacement: brake pads – BMW X5 E53. Tip from AUTODOC:
Make sure the pads are installed with linings facing the disc.
Step 21
Connect the brake pad wear sensor plug.
Step 22
Install the brake caliper and fix it. Use HEX No.H7. Use a torque wrench. Tighten it to 30 Nm torque.
Step 23
Install the dust boot caps of the brake caliper guide pins.
Step 24
Install the brake caliper retaining spring.
Step 25
Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 26
Install the wheel.
AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. BMW X5 E53
Step 27
Screw in the wheel bolts. Use wheel impact socket #19.
Step 28
Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 140 nm torque.
Replacement: brake pads – BMW X5 E53. Tip from AUTODOC experts:
Without starting the engine, press the brake pedal several times until you feel significant resistance.
Step 29
Remove the jacks and chocks.
Replacement: brake pads – BMW X5 E53. AUTODOC recommends:
Check the brake fluid level in the expansion tank and refill if necessary.
Step 30
Tighten the brake fluid reservoir cap.
Step 31
Install the protective cover.
Step 32
Install the rubber strip.
Step 33
Close the hood.
Replacement: brake pads – BMW X5 E53. Professionals recommend:
Slow down smoothly for first 150-200 km after the brake pads replacement. Avoid unneccessary and sharp braking to a stop.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 1
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the BMW X5 (E53) model.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.