Replace the brake disks on the car PEUGEOT 306 Convertible (7D, N3, N5) in complete set for each axis. Regardless of the state of components. This will ensure even braking.
The replacement procedure is identical for both brake disks on the same axle.
When changing the brake discs, always replace the brake pads.
Warning! Shut down the engine before starting any work – PEUGEOT 306 Convertible (7D, N3, N5).
Carry out replacement in the following order:
Step 1
Open the bonnet. Unscrew the brake fluid reservoir cap.
Step 2
Secure the wheels with chocks.
Step 3
Loosen the wheel mounting bolts. Use wheel impact socket #19.
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 15
Clean the brake disc fasteners. Use a wire brush. Use WD-40 spray.
Step 16
Unscrew the brake disc fastening. Use Torx T30. Use an impact screwdriver.
Step 17
Remove the brake disc.
Step 18
Clean the hub. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 19
Treat the brake caliper piston. Use a brake cleaner.
AUTODOC recommends:
Replacement: brake discs – PEUGEOT 306 Convertible (7D, N3, N5). After applying the spray, wait a few minutes.
Step 20
Press in the brake caliper piston. Use brake caliper wind back tool.
Step 21
Install the brake disc.
Step 22
Tighten the brake disc fastening. Use Torx T30. Use a torque wrench. Tighten it to 9 Nm torque.
Step 23
Install the brake caliper and fix it. Use a drive socket #19. Use a torque wrench. Tighten it to 110 Nm torque.
Step 24
Install the brake pads.
Step 25
Install the retainer of the brake pads. Use a crowbar.
Step 26
Install the brake pad retaining pin.
Step 27
Install the retaining springs of the brake pads.
Step 28
Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 29
Clean the brake disk surface. Use a brake cleaner.
Replacement: brake discs – PEUGEOT 306 Convertible (7D, N3, N5). Tip from AUTODOC experts:
After applying the spray, wait a few minutes.
Step 30
Install the wheel.
AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. PEUGEOT 306 Convertible (7D, N3, N5)
Step 31
Screw in the wheel bolts. Use wheel impact socket #19.
Step 32
Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 100 Nm torque.
Step 33
Remove the jacks and chocks.
AUTODOC recommends:
PEUGEOT 306 Convertible (7D, N3, N5) – Press the brake pedal several times with the engine shut down until you feel the resistance built up.Check the brake fluid level in the expansion tank and refill if necessary.
Step 34
Tighten the brake fluid reservoir cap. Close the hood.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the PEUGEOT 306 Convertible model