Disclaimer
How to change lambda sensor on VW Passat Saloon (362) – replacement guide
downloads:
1
Views:
147
Recommended replacement interval for the part category Lambda sensor : 100000 km
Important!
This replacement procedure can be used for:
VW Passat Saloon (362) 1.4 TSI, VW Passat Saloon (362) 1.8 TSI, VW Passat Saloon (362) 2.0 TSI, VW Passat Saloon (362) 1.4 TSI EcoFuel, VW Passat Saloon (362) 3.6 FSI 4motion, VW Passat Saloon (362) 1.4 TSI MultiFuel, VW Passat Saloon (362) 1.8 TSI … View more
The steps may slightly vary depending on the car design.
VW Passat Saloon (362) 1.4 TSI, VW Passat Saloon (362) 1.8 TSI, VW Passat Saloon (362) 2.0 TSI, VW Passat Saloon (362) 1.4 TSI EcoFuel, VW Passat Saloon (362) 3.6 FSI 4motion, VW Passat Saloon (362) 1.4 TSI MultiFuel, VW Passat Saloon (362) 1.8 TSI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Lambda Sensor for Passat Saloon (362) and other VW models
Alternative products

Electronic spray
High-temperature ceramic grease
Torque wrench
Drive socket # 10
22-mm oxygen sensor socket
Ratchet wrench
Thread tap
Fender cover
Replacement: lambda sensor – VW PASSAT (362). AUTODOC experts recommend:
- After replacing the oxygen sensor, clear the trouble code from the electronic control unit and let the ECU adapt itself to the new sensor.
- Before getting down to work, start the engine and let it warm up to operating temperature.
- Please note: all work on the car – VW PASSAT (362) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Open the bonnet.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3Lift the car using a jack or place it over an inspection pit.Step 4
Unscrew the fasteners of the oxygen sensor housing cover. Use a drive socket #10. Use a ratchet wrench. - Step 5
Remove the oxygen sensor housing cover. - Step 6
Detach the oxygen sensor connector. - Step 7
Unscrew the oxygen sensor fastener. Use a 22-mm oxygen sensor socket. Use a ratchet wrench. - Step 8
Remove the oxygen sensor. - Step 9
Cut the thread for the new oxygen sensor. Use a thread tap. Use a ratchet wrench. - Step 10Treat the oxygen sensor. Use high-temperature ceramic grease.Step 11
Install the new oxygen sensor. - Step 12
Tighten the oxygen sensor fastener. Use a 22-mm oxygen sensor socket. Use a torque wrench. Tighten it to 37 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VW Passat B7 Saloon (362) model
Popular maintenance tutorials for VW Passat B7 Saloon
Complete guides for changing the Oxygen sensor on different VW PASSAT models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VW Passat Saloon (362)
View more
Understanding Airbag Light Warnings | Essential Tips for Car Safety
Revitalize Your Car Interior: DIY Steering Wheel Cover with AUTODOC Tips
Don’t Replace, Restore: Fixing Damaged Threads at Home
How to fix your car with AUTODOC CLUB
Most commonly replaced car parts on VW PASSAT
Time to replace parts? Get even better deals in our Shop app.

SCAN ME




















