Disclaimer
How to change lambda sensor on SKODA SUPERB Estate (3T5) – replacement guide
downloads:
1
Views:
18
Recommended replacement interval for the part category Lambda sensor : 100000 km
Important!
This replacement procedure can be used for:
SKODA SUPERB Estate (3T5) 3.6 V6 4x4, SKODA SUPERB Estate (3T5) 1.8 TSI 4x4, SKODA SUPERB Estate (3T5) 1.8 TSI, SKODA SUPERB Estate (3T5) 1.4 TSI, SKODA SUPERB Estate (3T5) 2.0 TFSI, SKODA SUPERB Estate (3T5) 1.8 TSI 4x4, SKODA SUPERB Estate (3T5) 1.8 TSI … View more
The steps may slightly vary depending on the car design.
SKODA SUPERB Estate (3T5) 3.6 V6 4x4, SKODA SUPERB Estate (3T5) 1.8 TSI 4x4, SKODA SUPERB Estate (3T5) 1.8 TSI, SKODA SUPERB Estate (3T5) 1.4 TSI, SKODA SUPERB Estate (3T5) 2.0 TFSI, SKODA SUPERB Estate (3T5) 1.8 TSI 4x4, SKODA SUPERB Estate (3T5) 1.8 TSI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Lambda Sensor for SUPERB Estate (3T5) and other SKODA models
Lambda sensor
Lambda sensor
Lambda sensor for Superb II Estate (3T5) Petrol (260 hp)
Electronic spray
High-temperature ceramic grease
Torque wrench
Drive socket # 10
22-mm oxygen sensor socket
Ratchet wrench
Thread tap
Fender cover
Replacement: lambda sensor – SKODA SUPERB Estate (3T5). AUTODOC experts recommend:
- After replacing the oxygen sensor, clear the trouble code from the electronic control unit and let the ECU adapt itself to the new sensor.
- Before getting down to work, start the engine and let it warm up to operating temperature.
- Please note: all work on the car – SKODA SUPERB Estate (3T5) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Open the bonnet.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3Lift the car using a jack or place it over an inspection pit.Step 4
Unscrew the fasteners of the oxygen sensor housing cover. Use a drive socket #10. Use a ratchet wrench. - Step 5
Remove the oxygen sensor housing cover. - Step 6
Detach the oxygen sensor connector. - Step 7
Unscrew the oxygen sensor fastener. Use a 22-mm oxygen sensor socket. Use a ratchet wrench. - Step 8
Remove the oxygen sensor. - Step 9
Cut the thread for the new oxygen sensor. Use a thread tap. Use a ratchet wrench. - Step 10Treat the oxygen sensor. Use high-temperature ceramic grease.Step 11
Install the new oxygen sensor. - Step 12
Tighten the oxygen sensor fastener. Use a 22-mm oxygen sensor socket. Use a torque wrench. Tighten it to 37 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the SKODA Superb II Estate (3T5) model.
Popular maintenance tutorials for Skoda Superb 3t5
Free download PDF
1.04 MB
Free download PDF983.04 KB
Free download PDF3.21 MB
Free download PDF1.2 MB
Free download PDF604.16 KB
Free download PDF1.57 MB
Complete guides for changing the Oxygen sensor on different SKODA SUPERB models
Free download PDF890.88 KB
Free download PDF972.8 KB
Free download PDF1 MB
Free download PDF890.88 KB
Free download PDF890.88 KB
Free download PDF890.88 KB
Your profile is your personal assistant.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- - scan the QR code
- - download from App Store
- - download from Google Play
Tips & tricks for your SKODA SUPERB Estate (3T5)
View more
Top 5 mistakes when working in the engine bay | AUTODOC tips
How to wash your car in winter | AUTODOC tips
How to start a car after a long idle period | AUTODOC tips
How and why to check your oil | AUTODOC tips
